779959
4
Zoom out
Zoom in
Previous page
1/10
Next page
A B
A B
+=3-4mm
2
2
1
1
A
B
C
1 mm 1 mm
12
1 1
2 2
BC
B+C=2 mm
ENGLISHENGLISH
BRAKES
GENERAL BRAKE ADJUSTMENT
Your SCOTT bike is fitted with a reliable and well‑functioning braking system,
provided the brakes are correctly adjusted. Check by measuring the distance
between the brake shoes and the rim: it should be 1.5 to 2 mm.
Cable connection and adjustment of the (Dual Pivot) brake
1. Put the quick release lever in
the closed position.
2. Adjust the brake shoe
clearance (as shown in the
illustration) and secure the
cable with the pinch bolt nut.
Cable bolt tightening
torque 68 Nm
HOW TO CHANGE BRAKE PADS
1. Loosen the security screw with a 2 mm allen key.
2. Push the used brake pad out of the aluminum brake shoe.
3. Push the new brake pad into the brake shoe, according to the arrow showing the
mounting direction.
4. Tighten the security screw to approximately 1.5 Nm.
CALIPER BRAKE
Release counter nut A and turn adjustment screw B counter clockwise until the
distance between brake pads and rims is approx. 2mm on each side. Tighten
counter nut A.
If the adjustment screw B is released
already to the limit, then release cable
clamping screw C and turn adjustment
screw clockwise to its original position.
Close the caliper brake with your hand
to the rim, adjust the brake cable and
tighten clamping screw C. Please note
the Tightening Torques table at the end
of this manual.
quick release
lever
centering adjustment bolt
3mm allenkey
closed
open
Finally make the fine tuning with adjustment screw B as mentioned above. The
wheel needs to spin free without touching the brake pads. Fix counter nut A.
IMPORTANT!
Make sure that the brake works perfectly.
IMPORTANT!
Under wet conditions the brake performance can decrease which will result in a
prolongation of the braking distance.
5mm allen key
tightening torque :
6‑8 Nm (52‑69 in. lbs.)
inner cable lead
Spring tension
adjustment screw
Spring tension
adjustment screw
Depress lever
about 10 times
V‑BRAKE
1. While holding the shoe against the rim,
tighten the shoe fixing nut.
2. Pass the inner cable through the inner
cable lead, and after setting so that the
total of the clearances between the left
and right shoes and the rim is 2 mm
tighten the cable fixing bolt.
3. Adjust the distance with the spring
tension adjustment screws.
4. Depress lever about 10 times
07 |
BIKE USER MANUAL | BMXBMX | BIKE USER MANUAL
| 06
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scott BMX 2018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scott BMX 2018 in the language / languages: English as an attachment in your email.

The manual is 0.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scott BMX 2018

Scott BMX 2018 User Manual - German - 10 pages

Scott BMX 2018 User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info