335562
18
Zoom out
Zoom in
Previous page
1/60
Next page
18
GB
! The glue applied on the gaskets leaves traces of
grease on the glass. Before using the appliance, we
recommend you remove these with a special non-
abrasive cleaning product. During the first few hours
of use there may be a smell of rubber which will
disappear very quickly.
! A few seconds after the hob is connected to the
electricity supply, a buzzer will sound. The hob may
now be switched on.
Switching on the hob
To switch the hob on, press and hold the button
for about a second.
Switching on the cooking zones
Each cooking zone is controlled by a device
consisting of two buttons (- and +).
Press the + button to activate the hotplate, then
set the power to the level required using the - and
+ buttons.
To set the power to maximum, hold down the -
button briefly.
Booster function
The booster function for the rear cooking zones may
be used to shorten heating-up times. It is activated by
pressing the
button.
This function boosts the
power of the relevant
zone to 3000W.
It stops automatically
after 4 minutes. Until the
booster of one of the
rear zones is activated,
the front zones have a
maximum power of 600
W (e.g. if the left rear
hotplate booster is
activated, the power of the left front hotplate
decreases).
Switching off the cooking zones
Press the -button: the power of the cooking zone
will progressively decrease until it is switched off.
Alternatively, the - and + buttons may be
pressed simultaneously. This immediately returns
the power setting to 0 and the cooking zone
switches off.
Programming the cooking time
! All the cooking zones may be programmed for a
length of time between 1 and 99 minutes.
1. Switch the hotplate on and set the temperature.
2. Press the button corresponding to the hotplate
you want to programme.
3. Set the cooking time using the - and + buttons.
4. Confirm by pressing the
button.
The timer begins counting down immediately. A
buzzer sounds for about 1 minute and the cooking
zone switches off when the set programme has
finished.
Repeat the above procedure for each hotplate you
wish to programme.
Control panel lock
When the hob is switched on, it is possible to lock the
oven controls to avoid accidental changes to the
settings (by children, during cleaning, etc.). Press the
button to lock the control panel and the indicator
light above the button will be lit. To use any of the
controls (e.g. to stop cooking), you must switch off
this function: press the
button for a few moments,
the indicator light will switch off and the lock function
is removed.
Switching off the hob
Press button to switch the appliance off.
If the control panel lock is on, the controls will
continue to be locked even after the hob is switched
on again. In order to switch the hob on again, you
must first remove the lock function.
Start-up and use
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scholtes ti 7624 nr at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scholtes ti 7624 nr in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info