Manual Scholtes pmg 41 dcdr (page 17 of 72) (English, German, Dutch, French, Italian, Spanish)

335556

Zoom out

Zoom in

1/72

! Only use pipes and seals that comply with current

national regulations.

Checking the tightness of the connection

! When the installation process is complete, check

the pipe fittings for leaks using a soapy solution.

Never use a flame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than

default type (indicated on the rating plate at the base

of the hob or on the packaging), the burner nozzles

should be replaced as follows:

1. Remove the hob grids and slide the burners off

their seats.

2. Unscrew the nozzles using a 7 mm socket

spanner, and replace them with nozzles for the

new type of gas (see table 1 “Burner and nozzle

characteristics”).

3. Reassemble the parts following the above

procedure in the reverse order.

4. Once this procedure is finished, replace the old

rating sticker with one indicating the new type of

gas used. Sticker are available from any of our

Service Centres.

Replacing the nozzles on separate “double flame “

burners:

1. remove the grids and slide the burners from their

housings. The burner consists of 2 separate parts

(see figure);

2. unscrew the burers with a 7 mm wrench spanner.

The internal burner has a nozzle, the external

burner has two (of the same size). Replace the

nozzle with models suited to the new type of gas

(see table 1).

3. replace all the components by repeating the steps

in reverse order

• Adjusting the burners’ primary air :

Does not require adjusting.

• Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust the adjustment

screw, which is positioned in or next to the tap pin,

until the flame is small but steady.

3. Having adjusted the flame to the required low

setting, while the burner is alight, quickly change

the position of the knob from minimum to

maximum and vice versa several times, checking

that the flame does not go out.

4. Some appliances have a safety device

(thermocouple) fitted. If the device fails to work

when the burners are set to the low flame setting,

increase this low flame setting using the adjusting

screw.

5. Once the adjustment has been made, replace the

seals on the by-passes using sealing wax or a

similar substance.

! If the appliance is connected to liquid gas, the

regulation screw must be fastened as tightly as

possible.

! Once this procedure is finished, replace the old

rating sticker with one indicating the new type of gas

used. Stickers are available from any of our Service

Centres.

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet pipe (in

order to comply with current national regulations).

DATA PLATE

Electrical

connections

voltage of 220-240V ~ 50/60Hz

(see data plate )

This appliance conforms to the

following European Economic

Community directives:

-73/23/EEC dated 19/02/73 (Low

Voltage) and subsequent

amendments

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

- 93/68/EEC dated 22/07/93 and

subsequent amendments.

- 90/336/EEC dated 29/06/90 (Gas)

and subsequent amendments.

- 2002/96/EC

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scholtes pmg 41 dcdr in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scholtes pmg 41 dcdr Manual

Product: