Manual Scholtes HDB 9 (page 11 of 40) (English, German, Dutch, French, Italian)

491213

Zoom out

Zoom in

1/40

a. Rest the suction unit on a flat surface and thread

the lower part of the hood onto it.

b. Make all the electrical connections between the two

parts.

c. Fix the hood definitively to the suction unit with the

number and type of screws indicated in the figure.

1. Using a pencil, draw a line on the wall, extending

up to the ceiling, to mark the centre. This will

facilitate installation.

2. Rest the drilling template against the wall: the

vertical centre line printed on the drilling template

must correspond to the centre line drawn on the

wall, and the bottom edge of the drilling template

must correspond to the bottom edge of the hood.

3. Rest the support bracket on the drilling template so

that it coincides with the dotted rectangle, mark the

two outer holes and drill them, remove the drilling

template, insert 2 wall plugs and fix the hood

support bracket into place using two 5x45mm

screws.

4. Hang the hood on the bracket.

5. Adjust the distance of the hood from the wall.

6. Adjust the horizontal position of the hood.

7. Using a pencil mark the cooker hood permanent

drill hole inside the suction group (two drill holes

are necessary for fastening).

8. Remove the hood from the bracket.

9. Drill at the point marked (Ø8mm - see operation 7).

10. Insert 2 wall plugs.

11.Rest the chimney support bracket „G“ against the

wall, touching the ceiling. Use the support bracket

as a drilling template (the small slot formed on the

support must coincide with the line drawn on the

wall as above – operation 1) and mark 2 holes with

a pencil, drill the holes (Ø8mm), insert 2 wall plugs.

12.Fix the chimney support bracket to the wall using

two 5x45mm screws.

13.Hook the hood onto the bottom bracket.

14.Fix the hood into its final position on the wall

(ABSOLUTELY ESSENTIAL).

15.Connect a pipe (pipe and pipe clamps not

provided, to be purchased separately) for

discharge of fumes to the connection ring located

over the suction motor unit.

If the hood is to be used in ducting version, the

other end of the pipe must be connected to a

device expelling the fumes to the outside. If the

hood is to be used in filter version, then fix the

deflector F to the chimney support bracket G and

connect the other extremity of the pipe to the

connection ring placed on the deflector F.

16.Make the electrical connections.

17.Apply the chimney stacks and fasten them at the

top to the chimney support „G“ (17b) using 2

screws (17a).

18.Slide the bottom section of the chimney down until it

completely covers the suction unit and slots into the

housing provided on top of the hood.

19. Fix the lower stack of the chimney with 2 screws.

Remount the carbon filter frame and the fat/s filter/s

and check the perfect functioning of the hood.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scholtes HDB 9 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scholtes HDB 9 Manual

Product: