491213

Scholtes HDB 9 Manual

10
Zoom out
Zoom in
Previous page
1/40
Next page
10
EN
! It is important to conserve this booklet for
consultation at any moment. In the case of sale,
cession or move, make sure it is together with the
product.
! Read the instructions carefully: there is important
information about installation, use and safety.
! Do not carry out electrical or mechanical variations
on the product or on the discharge conduits.
! Your hood is ready to be used in the suction version.
To use the filtering version, you must order the suitable
kit where you will find all the necessary details.
The information for transforming the hood from the
suction version to the filtering version is already
contained in the manual supplied with the product.
Installation
Electrical connection
The mains power supply must correspond to the rating
indicated on the plate situated inside the hood. If
provided with a plug connect the hood to a socket in
compliance with current regulations and positioned in
an accessible area. If it not fitted with a plug (direct
mains connection) or if the plug is not located in an
accessible area apply a bi-polar switch in accordance
with standards which assures the complete
disconnection of the mains under conditions relating to
over-current category III, in accordance with
installation instructions.
Warning: Before re-connecting the hood circuit to the
mains supply and checking the efficient function,
always check that the mains cable is correctly
assembled.
Connection to a discharge tube
Connect the hood and discharge holes on the walls
with a diameter equivalent to the air outlet (connection
flange).
Using the tubes and discharge holes on walls with
smaller dimensions will cause a diminution of the
suction performance and a drastic increase in noise.
Any responsibility in the matter is therefore declined.
! The company declines any responsibility whenever
these regulations are not respected.
Preliminary information for installation of the hood:
Disconnect the hood during electrical connection, by
turning the home mains switch off.
Remove the fat/s filter/s and the carbon filter frame.
Do not tile, grout or silicone this appliance to the wall.
Surface mounting only. Do not fix chimney flue to
furniture or fly over shelves unless the chimney flue can
be easily removed, in case maintenance is ever
required.
Assembling the chimney flue support/bracket (3 parts):
The three parts should be fixed with 4 screws, the
support extension is adjustable and should correspond
to the internal width of the telescopic chimney flue.
Assembling the deflector (only when a deflector
composed of 3 parts is supplied – the deflector should
be only for the filter version):
The three parts should be fixed with 2 screws, the
deflector extension is adjustable and should
correspond to the width of the chimney flue support, to
which it is then fixed.
The minimum distance between the supporting surface
for the cooking vessels on the hob and the lowest part
of the range hood must be not less than 50cm from
electric cookers and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify
a greater distance, this must be adhered to.
Expansion wall plugs are provided to secure the hood
to most types of walls/ceilings. However, a qualified
technician must verify suitability of the materials in
accordance with the type of wall/ceiling. The
wall/ceiling must be strong enough to take the weight
of the hood. Do not tile, grout or silicone this appliance
to the wall. Surface mounting only.
Installation
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scholtes HDB 9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scholtes HDB 9 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info