782130

Scheppach UG700 Manual

17
Zoom out
Zoom in
Previous page
1/48
Next page
international 17
m Electrical Connection
Connecting the electrical equipment, or any repair work,
may only be carried out by a qualified electrician.
The built-in electric motor is already connected and ready
for operation. The connection conforms to the relevant
VDE (German Association for Electrical, Electronic and
Information Technologies) and DIN (German Institute for
Standardization) regulations.
The connection to the mains supply made by the custom-
er, as well as the extension cord used, must comply with
these regulations.
Important Notes
Faulty power cords
Power cords often suffer insulation damage.
Causes are:
• Pinching when power cords are routed through windows
or door cracks.
• Bending due to improper attachment or routing of the
power cords.
• Cuts due to driving over the power cords.
• Insulation damage caused by yanking the mains plug
out of the power outlet.
• Cracks in the insulation due to ageing.
Such faulty power cords must not be used and are a danger
to life because of the damaged insulation!
Inspect the power cords for damage on a regular basis.
Make sure that during this inspection the power cord is not
connected to the mains supply.
The power cords must comply with the applicable VDE
(German Association for Electrical, Electronic and In-
formation Technologies) and DIN (German Institute for
Standardization) regulations. Only use power cords marked
as H 07 RN.
A type identification printed on the power cords is pre-
scribed.
AC Motor
• The power supply must be 230–240 V/50 Hz.
• Extension cords must have a minimum conductor cross
section of 1.0 square millimetres.
• The connection to the power supply must be protected
with a 16 A (delayed-action) fuse/ circuit breaker.
When you have questions, please include the following de-
tails:
• Motor manufacturer
• Type of current
• The details from the type plate of the machine
• The details from the type plate of the switch
Always send back the whole drive unit including the switch,
when you return the motor.
m Raccordement électrique
Les raccordements et les réparations électriques ne peu-
vent faits que par un spécialiste en électricité.
Le moteur électrique est pr t à l’emploi. Le raccordement
correspond aux normes VDE et DIN correspondantes.
Le raccordement au secteur du client ainsi que les câbles
à rallonge utilisés doivent correspondre à ces normes.
Informations importantes
Câbles électriques défectueux
Les câbles électriques présentent souvent des défauts
d’isolation
Causes:
• Marques de pression si les câbles sont passés par l’en-
trebâillement de fen tres ou de portes.
• Coudes causés par une fixation ou une conduite non
appropriée des câbles électriques.
• Coupures dues à l’écrasement des câbles
• Défauts d’isolation dus aux arrachement du câble de la
prise murale.
• Fissures dues au vieillissement de l’isolation.
De tels câbles électriques défectueux ne peuvent pas tre
utilisés et représentent un danger mortel en raison des dé-
fauts d’isolation.
Contrôlez régulièrement si les câbles électriques ne sont
pas endommagés. Veillez à ce que les câbles ne soient pas
raccordés au secteur pendant le contr ôle.
Les câbles électriques doivent correspondre aux normes
VDE et DIN correspondantes. Utilisez uniquement des câ-
bles portant le sigle H07-RN.
L’impression de la désignation du type sur le câble est
obligatoire.
Moteur à courant alternatif
• La tension du réseau doit tre de 230–240 V/50 Hz.
• Les câbles à rallonge doivent avoir un diam tre minimal
de 1,0 millim tre carré
• Le raccordement au secteur est sécurisé par un fusible
temporisé 16 A
Pour une demande de renseignement veuillez indiquer les
données suivantes:
• Fabricant du moteur
• Type de courant du moteur
• Données de la plaque de type de la machine
• Données de la plaque de type de l’interrupteur
En cas de renvoi du moteur, renvoyez l’unité de propulsion
compl te avec l’interrupteur.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach UG700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach UG700 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2.08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info