782536
29
Zoom out
Zoom in
Previous page
1/48
Next page
29 І 48
Cutting narrow workpieces, Fig. 25
Be sure to use a push stick when making longitudinal
cuts in workpieces smaller than 120 mm in width. A
push block is supplied with the saw! Replace a worn
or damaged push stick immediately.
Adjust the parallel stop to the width of workpiece
you require.
Feed in the workpiece with two hands. Always use
the push stick in the area of the saw blade.
Always push the workpiece through to the end of
the splitter.
Caution! With short workpieces, use the push stick
from the beginning.
Cutting edges and strips, Fig. 26
Operating cycle: Mount the fence with a low stop bar
surface or use an auxiliary fence. Feed the work-
piece with a push-stick until the end of the workpiece
is in the region of the riving knife. Prevent long work-
pieces from toppling over at the end of the cutting
process by using a table length extension.
Making cross cuts, Fig. 27
Operating cycle: Adjust the rejection rail so that
workpiece sections do not touch the ascending part
of the sawblade. Only feed the workpiece by means
of a crossfeed stop or a cross slide.
Do not remove wood chippings from the region of the
workpiece with your hands.
11. Cleaning and Maintenance
Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
down with compressed air at low pressure.
We recommend that you clean the equipment im-
mediately after you use it.
Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plastic
parts in the equipment. Ensure that no water can
get into the interior of the equipment.
In order to extend the service life of the tool, oil
the rotary parts once monthly. Do not oil the motor.
12. Storage
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Cover the electrical tool in order to protect it from
dust and moisture.
Store the operating manual with the electrical tool.
In times of non-use keep the push stick or the push
block with the electrical power tool at all times.
Saw Blade – Diagonal Adjustment
The saw blade may be swiveled from 9to 45° after
the wing nut has been loosened.
After each new adjustment it is advisable to carry out a
trial cut in order to check the set dimensions.
Readjust the angle adjustment on the adjusting bolts 1
& 2.
Saw Blade Height Adjustment
The saw blade is adjustable from 0 to 83 mm cutting
height after the wing nut has been loosened.
For safe and clean working, choose a minimal saw
blade projection for the workpiece.
Dem Spaltkeil wie im Bild 22 gezeigt einstellen.
Adjust the riving knife as shown in picture 22.
The riving knife is an important safety device which
guides the workpiece and prevents the cutting joint from
closing behind the saw blade and the workpiece from
being kicked backwards. Check the riving knife thick-
ness. The riving knife should never be thinner than the
body of the saw blade or thicker than the cutting joint
width.
Only use saw blades with a diameter of 315 mm and a
thickness of 2.4 mm (3.0 mm teeth).
Lower the suction hood onto the workpiece during every
working cycle. The hood must be positioned horizon-
tally above the saw blade during every working cycle.
Length Cuts
Insert the length stop for parallel cuts.
Use the stop ruler with the high stop side for cuts above
120 mm and the stop ruler with the low stop side for cut
widths under 120 mm.
Lead the workpiece with the push stick.
Diagonal Cuts
For diagonal and angle cuts, insert the cross-cutting
guide.
Operational Information
Working on circular saws
Cutting wide workpieces, Fig. 24
Width of the workpiece to be machined over 120 mm
Operating cycle: Adjust the ripping fence in accordance
with the width of the workpiece. Ensure that your hands
are resting in a safe place. The workpiece may only be
forward-fed in the tool area with the right hand or with
the aid of a push-stick if narrow workpieces are cut off
in the cutting process. Move the fence back to the mid-
dle of the saw or use a short auxiliary fence if there is
a danger of the workpiece being jammed between the
circular sawblade, the riving knife and the fence.
Only the upper suction hood has been left out in the
individual case in order to display the operating cycle or
device more clearly.
The upper suction hood is required for all of the operat-
ing cycles.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach TS2800 Primaster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TS2800 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 6.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info