Manual Scheppach TS2800 Primaster (page 27 of 48) (English, German, French)

782536

Zoom out

Zoom in

1/48

27 І 48

Attachment

Important. Pull out the power plug before carrying out

any maintenance, resetting or assembly work on the

circular saw!

Place all parts supplied on a at surface. Grouping

equal parts.

Note: If compounds with a bolt (round head / or hexa-

gon), hex nuts and washers are backed up, the wash-

er must be tted under the nut.

Insert screws each from outside to inside. Secure

connections with nuts on the inside.

Note: Tighten the nuts and bolts during assembly

only to the extent that they can not fall down.

If you tighten the nuts and bolts prior to nal assem-

bly, nal assembly can not be performed.

Fig. 1

Place the table top (1) onto a work bench after having

removed the packing pad a underneath the motor.

Fig. 1.1

Fasten the base leg (2) onto the table top using 2

hexagon bolts M6 x 16, 2 washers 6 and 2 nuts M6.

Tighten the bolts slightly by hand.

Fig. 2

Fasten the switch (6) to the table top using 2 hexagon

bolts M6 x 16, 2 washers 6, and 2 nuts M6.

Fig. 3

Fasten the base leg (3) to the table top using 2 hexa-

gon bolts M6 x 16, 2 washers 6, and 2 nuts M6.

Fig. 4

Fasten the base leg (4) to the table top using 2 hexa-

gon bolts M6 x 16, 2 washers 6, and 2 nuts M6.

Fig. 5

Fasten the base leg (5) and the hose holder to the

table top using 2 hexagon bolts M6 x 16, 2 washers

6, and 2 nuts M6.

Fig. 6 / 6.1

Fasten 2 longitudinal braces (10) and 2 cross braces

(9) onto the base legs (2, 3,4 and 5) using 12 hexa-

gon bolts M6 x 16, 12 washers 6, and 12 nuts M6.

Fig. 7 / 7.1 / 7.2 / 7.3

Fasten the table extension plate (8) with 2 braces

11 and cross brace to the table top using 6 hexagon

bolts M6 x 16, 6 washers 6, and 6 nuts M6.

Tighten the bolts slightly by hand. (The table length

extension (8) can also be used as table width exten-

sion by tting it to the side with the shorter braces.)

Fig. 8

Fasten the suction piece (14) to the lower saw blade

guard (13) using 4 hexagon bolts M4 x 10.

7. Technical Data

AC motor w 400V 50Hz

performance 2800 W

operating mode S6 40%*

Idle speed 2800 min-1

Hard-metal blade ø 315 x ø 30 x 3 mm

Number of teeth 24

table size 800 x 550 (950) mm

Cutting height max. 90° 83 mm

Cutting height max. 45° 49 mm

height adjustment 0 - 83 mm

saw blade swivel 0 - 45°

weight 47 kg

* operating mode S6 40%: Continuous opera-

tion with intermittent loading (playing time 10 min).

Engine protection of to hot warming up:

It´s allowed to run the engine with nominal power maxi-

mum 40% of playing time. After this the machine must run

60% of playing time steadily without load.

Noise values

The total noise values determined in accordance

with EN 61029.

sound pressure level LpA 94,5 dB(A)

uncertainty KpA 3 dB

sound power level LWA 105,2 dB(A)

uncertainty KWA 3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing.

Total vibration values (vector sum - three directions)

determined in accordance with EN 61029.

8. Attachment and operation

Before starting the equipment

• All covers and safety devices have to be properly

tted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws, etc.

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power

supply make sure the data on the rating plate are

dentical to the mains data.

• Connect the machine to a properly installed pro-

tective contact socket, with at least 16A circuit

breaker.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TS2800 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 6.8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach TS2800 Primaster Manual

Product: