782536
23
Zoom out
Zoom in
Previous page
1/48
Next page
23 І 48
2. Machine description (Fig. A)
1. On/off switch
2. Longitudinal stop
3. Saw blade
4. Protective cover
5. Extraction hose
6. Riving knive
7. Stage centre
8. Table extension
9. Wheel kit
10. Extraction connection piece
11. Transport handle
12. Height adjustment wheel
3. Scope of delivery
Open the packaging and remove the device care-
fully.
Remove the packaging material as well as the
packaging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for trans-
port damage.
If possible, store the packaging until the warranty
period has expired.
Attention
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, lm and small parts! There is a risk of swal-
lowing and suffocation!
4. Intended use
The bench-type circular saw is designed for the slit-
ting and cross-cutting of all types of timber, commen-
surate with the machine’s size.
The machine is not to be used for cutting any type of
roundwood.
The machine is to be used only for its prescribed pur-
pose. Any use other than that mentioned is consid-
ered to be a case of misuse. The user/operator and
not the manufacturer shall be liable for any damage
or injury resulting such cases of misuse.
The machine is to be operated only with suitable saw
blades. It is prohibited to use any type of cutting-off
wheel. To use the machine properly you must also
observe the safety regulations, the assembly instruc-
tions and the operating instructions to be found in this
manual. All persons who use and service the machine
have to be acquainted with this manual and must be
informed about its potential hazards. It is also impera-
tive to observe the accident prevention regulations in
force in your area. The same applies for the general
rules of occupational health and safety.
Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage.
1. Introduction
Manufacturer:
Woodster GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
Improper handling,
Non-compliance of the operating instructions,
Repairs by third parties, not by authorized service
technicians,
Installation and replacement of non-original spare
parts,
Application other than specied,
A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recom1mend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating
the machine and carefully follow its information. The
machine can only be operated by persons who were
instructed concerning the operation of the machine
and who are informed about the associated dangers.
The minimum age requirement must be complied
with. In addition to the safety requirements in these
operating instructions and your country’s applicable
regulations, you should observe the generally rec-
ognized technical rules concerning the operation of
woodworking machines.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach TS2800 Primaster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TS2800 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 6.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info