782524
23
Zoom out
Zoom in
Previous page
1/40
Next page
23
Replacing the saw blade, fig. 14.1-14.2
J
You must wear gloves when handling the saw bla-
de.
Turn the height adjuster wheel (2) until the saw blade
has reached its highest position.
Remove the protective hood (5).
Remove the table insert (13).
Lock the arbor with the saw blade key (G).
Use the flat spanner (H) to loosen the saw blade nut
(M) by turning it anti-clockwise (right-hand thread).
Remove the outer flange (K) and pull off the saw blade.
Clean both flanges carefully before attaching a new
saw blade.
Attach and secure the saw blade in reverse order.
Warning: Be aware of the saw blade’s direction of ro-
tation. The cutting edge of the teeth must point in the
direction of travel, i.e. forwards (see the arrow on the
saw blade).
Assemble the table insert again.
Before working with the saw again, make sure that all
safety equipment is functional. Important: After as-
sembly, check by turning with your hand that the saw
blade rotates smoothly.
Connect the saw blade to the power supply and leave
it in idle before starting to saw.
WARNING
m
There are no parts inside the power tool which can
be maintained by the user! Never open the power
tool! Take it to a qualified expert for further maintenance
work!
REPAIRS
Damage must exclusively be repaired by qualified tech-
nical staff.
WARNING
m
If the mains cable or the mains plug is damaged, it
has to be replaced by an electrician to prevent risks.
WARNING
m
After carrying out any cleaning and maintenance
work, make sure all safety equipment, if present, is
attached correctly and safely. Never use the power tool wit-
hout safety equipment!
Storage and Transport
STORAGE
1 Clean the power tool as described in section “Cleaning”.
2 Store the power tool and its accessories in a dark, dry,
frost-free and well-ventilated place out of the reach
of children. The ideal storage temperature is between
10 and 30°C.
3 Wrap the mains cable around the cable organiser on
the back of the power tool when you are not using it.
4 Cover the power tool to protect it from dust and hu-
midity.
5 Keep the operating manual with the power tool.
Storing the push stick and the mitre gauge, fig. 15
When you are not using the mitre gauge and the push
stick, they can be stored on the side in the bracket.
AC motor
The power voltage has to be 230 Volt – 50 Hz.
Extension leads up to 25 m in length must have a
cross section of 1.5 mm2, at more than 25 m length,
it has to be at least 2.5 mm2.
The mains connection is protected against short circuit
with a 16 A slow fuse.
Connections and repairs to the electrical equipment may
only be carried out by a trained electrician.
If there are any questions, please provide the following
data:
Motor manufacturer
Motor’s type of power
Data from the machine’s type plate
When sending back the motor, always send the entire mo-
tor unit with switch.
Follow the safety notices!
Cleaning, Maintenance and Repair
WARNING
mBefore working on the power tool itself (e.g.
transport, set-up, retooling, cleaning and
maintenance), disconnect the mains plug from the
socket!
CLEANING
1 Always leave the power tool to cool down after use.
2 Clean the power tool after every use with a damp cloth
and some soap. Use a paint brush or a brush for areas
which are difficult to access.
Note: Do not use aggressive cleaning agents or solvents.
They may affect the plastic and metal parts of the power
tool.
3 Regularly free the inside of the power tool from resi-
dual wood and chippings, such as the tooth segment
and gear of the revolving mechanism.
4 Remove possible saw dust blockages from the extrac-
tion port with a suitable blunt tool.
WARNING
m
Do not remove blockages with hands or fingers!
5 Remove particularly persistent residual dust in in-
accessible places with compressed air (max. 3 bar).
MAINTENANCE
Before and after every use, check the power tool as well
as the accessories (e.g. tool attachments) for wear and
tear and damage. If required, replace them with new ac-
cessories as described in this operating manual. Comply
with technical requirements for this.
1 Check the saw blade regularly. Use well-sharpened,
flawless and true saw blades only. Only use tools which
comply with the European Standard EN 847-1.
2 Immediately replace a worn-out table insert with a
new one of the same type.
3 Always keep the table’s surface free from resin.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach TS251 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TS251 in the language / languages: English, German, French as an attachment in your email.

The manual is 5.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info