Manual Scheppach TS251 (page 20 of 40) (English, German, French)

782524

Zoom out

Zoom in

1/40

back of the handwheel.

4 Push the handle, with the screw at the front, into the

opening of the handwheel.

5 Tighten the handle’s screw and close the handle’s

opening again with the lid.

STEP 3.

ASSEMBLY OF THE TABLE EXTENSION, FIG. 4.1 – 4.2

1 x Tabletop

2 x Allen key

2 x Open-end spanner

1 Pull the two shafts (B) of the chipping bag bracket

to the outside and remove the Allen screws and the

washers.

2 Attach the tabletop (2) by pushing it onto the shafts.

3 Make sure the ends of the shafts overlap with the

holes on the tabletop.

4 Fix the chipping bag bracket to the tabletop and tigh-

ten the screws.

5 Fix the tabletop (2) with two Allen screws (D) to the

shafts (B).

6 Fix the chipping bag (8) with the Velcro to the table

extension.

STEP 4.

ASSEMBLY OF THE RIVING KNIFE, FIG. 5.1 – 5.2

1 Riving knife

2 Saw blade guard

1 Remove the table insert.

2 Move the saw blade to its highest position by turning

the handwheel anti-clockwise for height adjustment.

Loosen the riving knife clamp (E). Fig. 5.1

3 Move the riving knife (4) to the speciﬁed position.

Make sure the ﬂanges of the riving knife bracket en-

gage with the holes of the riving knife.

4 Tighten the riving knife clamp (E) again.

Fig. 5.2

5 Put the table insert back.

STEP 5.

USING THE TRANSPORT DEVICE, FIG. 8

1 Push the button underneath the handle (F) and pull

the telescope handle up until it engages.

2 Tilt the power tool slightly towards you so that it com-

pletely stands on the wheels.

3 Pull the power tool to the speciﬁed position and set

it up as described in Step 1.

4 Ensure a secure position and solid ground

STEP 6.

ASSEMBLY OF THE SAW BLADE GUARD, FIG. 6

1 Protective hood

1 Extraction hose

1 In order to assemble the saw blade guard (5), place

it over the riving knife (4) so that the screw ﬁts into

the slot of the riving knife.

2 Tighten the wing nut sufﬁciently so that the saw blade

guard stays moveable but lifts when the work piece is

Description, ﬁg. 1

1 On-/off-switch

2 Adjuster wheel

3 Saw blade

4 Riving knife

5 Saw blade guard

6 Longitudinal stop

7 Table extension

8 Chipping bag

9 Transport wheel

10 Frame foot r.

11 Frame foot l.

12 Extraction hose

13 Table insert

Assembly

Any assembly and retooling work may only take place with

the mains plug removed.

Due to packaging reasons, this power tool is not comple-

tely assembled.

• Open the box and remove packaging and Styrofoam

parts.

• Remove the supplied components.

• Take the power tool from the box and put it on the

ﬂoor, using some cardboard as a base to protect the

surface.

Note: This power tool is heavy, two people should remove

it from the box.

Place all supplied parts on a ﬂat surface. Group the same

parts.

Note: If connections are secured with a screw (round head

or hexagon head), hexagon nuts and washer, the washer

has to be ﬁxed under the nut. Insert the screws from the

outside to the inside, secure connections with nuts from

the inside.

Note: During assembly, tighten nuts and screws only so

much that they cannot fall off. If you tighten nuts and

screws completely before the ﬁnal assembly, the ﬁnal as-

sembly cannot be carried out.

STEP 1. SET-UP, FIG. 2

1 Put the power tool on its side so that it stands on the

wheels and the rubber buffers.

2 Loosen the wing nuts (A).

3 Fold the frame (10) up and push it into the track.

4 Tighten the wing nuts again.

5 Repeat this process for the second frame (11).

STEP 2.

ASSEMBLY OF THE HANDWHEEL, FIG. 3

1 x Handle

1 x Allen key

1 x Open-end spanner

1 Remove the lid of the handle using a screwdriver.

2 Remove the nut from the handle.

3 Place the nut into the recess speciﬁed for this at the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TS251 in the language / languages: English, German, French as an attachment in your email.

The manual is 5.21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach TS251 Manual

Product: