Manual Scheppach TS251 (page 18 of 40) (English, German, French)

782524

Zoom out

Zoom in

1/40

the type of material you will work on, the impor-

tance of local deposition (acquisition or source)

and the proper adjustment of covering/ deﬂecting

plate/ guide.

–Do not use saw blades made out of highspeed steel

(HSS steel).

–In times of non-use keep the push stick or the push

block with the electrical power tool at all times.

2 Maintenance and repair

–The noise level depends on different factors such

as the quality of the saw blades, the condition of

saw blade and power tool. If possible, use saw

blades that were constructed for noise reduction,

maintain the electrical power tool and tool adapter

regularly and keep them in good condition in order

to reduce the noise level.

–Inform the person who is responsible for the secu-

rity of the power tool immediately when you detect

defects in the electrical power tool, the protection

equipment or the tool.

3 Working safely

–Use the push stick or a push block to pass the work

piece by the saw blade safely.

–Do not carry out folds or grooves without using

proper protective devices over the saw table.

–Do not use this electrical power tool to create sla-

shes (grooves ﬁnished on the work piece itself).

–Use only saw blades for which the maximum speed

is lower than the maximum spindle

–speed of the table saw and which are suitable for

the material you intend to cut.

–Always use the transporting means for the transport

of the electrical power tool. Never use the protecti-

ve devices for handling and transporting the device.

–Make sure that the upper part of the saw blade is

covered; e.g. by the protective device.

Warning! During operation this electrical power tool pro-

duces an electromagnetic ﬁeld which can inﬂuence acti-

ve or passive medical implants under certain conditions.

In order to avoid the risk of serious or fatal injuries, we re-

commend persons with medical implants to consult with

their doctor and the manufacturer of the medical implant

before operating the electrical power tool.

SAFETY INFORMATION FOR HANDLING SAW BLADES

1 Operate insertion tools only when you know how to

handle them correctly.

2 Always consider the maximum speed. The maximum

speed indicated on the power tool may not be excee-

ded. Observe the speed range (if speciﬁed).

3 Do not use insertion tools with cracks.

4 Immediately take ruptured insertion tools out of ser-

vice; simply repairing them is not admissible.

5 Clean the clamping surfaces of dirt, fat, oil and water.

6 Always handle insertion tools with care. If possible,

keep them in their original packing or in a special

container. Wear protective gloves in order to improve

–Keep the handles dry, clean and free from oil and

fat.

–Be sure that the device is not in use , before main-

tenance and while changing tools like saw blades,

drills or any kind of machine tools.

–Before turning the machine on, make sure that

all keys and adjustment tools have been removed.

–Make sure that the switch is turned off when plug-

ging the plug in the socket.

–For outdoor work, use only extension cables which

are approved for this purpose.

–Always pay attention and take the utmost care when

working with an electric power tool. Do not use the

power tool when you are not concentrated.

–Before further using the power tool, protective de-

vices and other parts have to be checked carefully

in order to make sure that they function perfectly

and properly.

–Check to see if all movable parts function properly

and that they do not jam and make sure that no

parts are damaged. All parts have to be mounted

properly and have to comply with all conditions in

order to ensure perfect operation of the power tool.

–Damaged protective devices and parts have to be

repaired or replaced as intended by an acknow-

ledged specialized workshop, if not speciﬁed other-

wise in the operating instructions.

–Damaged switches have to be replaced in a custo-

mer service repair shop.

–Do not use power tools where the switch cannot

easily be turned on and off.

–Using other application tools and accessories can

cause a risk of personal injury.

–This electrical power tool complies with the rele-

vant safety regulations.

–Repairs may only be carried out by an expert who

uses original spare parts; otherwise

–the operator runs the risk of accidents.

ADDITIONAL SAFETY INFORMATION

1 Safety precautions

–Replace worn out stage plates.

–Use only saw blades which are recommended by the

manufacturer and which correspond to EN 847-1.

Warning! When replacing the saw blade, ensure

that the cutting width is not narrower and that the

main blade width is not wider than the width of

the splitting wedge.

–Make sure, that you select a saw blade that is ap-

propriate for the material you intend to cut.

–Wear appropriate, personal protective equipment

such as:

–Ear protection to reduce the risk of getting hard

of hearing

–Respiratory protection to reduce the risk of in-

haling dangerous dust

–Be sure to wear gloves when working with saw

blades and coarse materials

–Where practicable, keep saw blades in a separate

container.

–Connect the power tool to a dust reception facility

when cutting wood. Dust release is inﬂuenced by

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TS251 in the language / languages: English, German, French as an attachment in your email.

The manual is 5.21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach TS251 Manual

Product: