782521
27
Zoom out
Zoom in
Previous page
1/240
Next page
27
Sahanterän kulman säätäminen, kuva 8
Vapauta sahanterän lukitus (11) ja käännä käsipyörää
(12) kunnes osoitin (15) osoittaa oikeaan kulmaan
asteikossa (14).
Kulman osoitinta (15) voidaan säätää tarkistettaessa
sahanterän kulman tarkkuutta. Aseta kulma sahanterää
vasten sahan ollessa poissa päältä ja irrotettuna virta-
lähteestä. Säädä käsipyörää, kunnes sahanterä on kul-
man suuntaisesti. Aseta sitten osoitin kohtaan 0°.
Lukitse säädön jälkeen.
Sahanterän vaihtaminen, kuva 10
Varoitus: Katkaise virta ja irrota saha virtalähteestä ennen
minkäänlaisten säätöjen tai huoltotoimenpiteiden suorit-
tamista tai sahanterän vaihtamista.
Käytä hansikkaita, kun käsittelet sahanteriä.
Käännä korkeussäätöratasta, kunnes sahanterä on kor-
keimmassa asennossaan.
Poista sahanterän suojus (17).
Poista penkkielementti (12).
Käytä sahanteräavainta sahanteräruuvin avaamiseksi
kääntämällä vastapäivään (kierre oikealle).
Pidä karaa 13 mm mutteriavaimella (ei sisälly toimi-
tukseen).
Poista ulkopuolen laippa ja irrota sahanterä.
Puhdista molemmat laipat huolellisesti ennen kuin
asennat uuden terän.
Asenna ja kiinnitä sahanterä paikalleen seuraamalla
ohjeita päinvastaisessa järjestyksessä.
Varoitus: Huomaa sahanterän pyörimissuunta. Hampai-
den leikkauspinnan tulee osoittaa pyörimissuuntaan, eli
eteenpäin (katso nuoli sahanteräs).
Asenna sahanterän suojus paikalleen.
Ennen kuin käytät sahaa, varmista, että kaikki turva-
laitteet toimivat oikein. Tärkeää: asentamisen jälkeen
tarkista pyörittämällä sahanterää käsin, että se pääsee
pyörimään vapaasti.
Kytke saha virtalähteeseen ja anna sen käydä hetki
ennen sahaamisen aloittamista.
Työskentelyohjeet
Pöytäpyösahoilla työskentely
Leveiden työkappaleiden sahaaminen, Kuva 19
(Työstökappaleen leveys yli 120 mm)
Työkalut: halkaisuun tarkoitettu pyösahanterä
Työvaihe: Säädä halkaisuvaste niin, että se vastaa käsit-
telyn alaisen työkappaleen leveyttä. Käden täytyy olla sen
päällä tukevasti. Jos halkaistaan kapeita työstökappaleita,
suoritetaan työntö eteenpäin työkalun alueella vain oikeal-
Adjusting the saw blade angle, Fig. 8
Loosen the saw blade lock (11) and turn the handle
(12) until the indicator (15) points to the correct angle
on the scale (14).
The angle indication (15) can be adjusted when check-
ing the angle accuracy of the saw blade. Hold an angle
against the saw blade when the machine is switched
off and the power supply unit is disconnected. Adjust
the handle until the saw blade is parallel to the angle.
Then, move the indicator to 0° on the scale.
Lock after adjusting.
Replacing the saw blade, Fig. 10.
Warning: Switch the machine off and disconnect the pow-
er supply unit before making any adjustments or carrying
out maintenance works, or replacing the saw blade.
Wear gloves when handling the saw blade.
Turn the height adjusting crank until the saw blade
reaches its highest position.
Remove the saw blade protector.
Remove the bench insert.
Use the saw blade key to loosen the saw blade screw
by turning in counter-clockwise direction (right-handed
threat).
Fix the spindle with a 13mm flat-end wrench (not in-
cluded in the delivery).
Remove the outer flange and pull the saw blade off.
Clean both flanges carefully before mounting a new
saw blade.
Mount and secure the saw blade in reversed order.
Caution: Observe the rotating direction of the saw
blade. The cutting edge of the saw teeth must point
in the direction of movement, i.e. forwards (see arrow
on the saw blade).
Re-attach the saw blade protector.
Before working with the saw, make sure that all safe-
ty equipment is functioning. Important note: After
mounting, make sure that the saw blade moves freely
by turning it manually.
Connect the saw to the mains voltage and let it run
idle, before starting to cut.
Working instructions
Working with circular saw benches
Cutting wide workpieces, Fig. 19.
Width of the workpiece to be cut is more than 120 mm.
Tool: circular saw blade for longitudinal cuts
Process steps: Adjust the longitudinal stop according to
the intended width of the workpiece. Mind the position of
your hand. If narrow pieces are cut off, the workpiece is
moved forward in the tool area only with the right hand or
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach TKS 1500S Herkules at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TKS 1500S Herkules in the language / languages: All languages as an attachment in your email.

The manual is 3.78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info