Manual Scheppach TIGER 2500 (page 10 of 52) (English, German, Dutch, Danish, French, Italian, Spanish, Finnish)

781684

Zoom out

Zoom in

1/52

10 english

A.C. Motor

• The supply voltage must be 220÷240 V/50 Hz.

• Extension lines up to a length of 25 m must have a

minimum cross section of 1.5 mm², lines with a length

exceeding 25 m must have a minimum cross section of

2.5 mm².

• The mains connection is protected with a maximum of 16 A.

Connections and repairs of the electrical equipment may

only be performed by an electrician.

If you have further questions, please specify the following:

• Motor manufacturer and type

• Kind of current of the motor

• Data from the machine type plate

• Data of the electric control

If you return the motor, always return the complete drive unit

with the electric control.

Working Instructions

Direction of Grinding (Fig. 1, Fig. 2)

It mainly depends on your requirements whether you

want to work with or against the direction of grinding. If

you want to quickly remove large quantities of steel (e.g.

from very old, rusty tools) or if you want to grind coarse

tools, such as axes, it is recommended to work against the

direction of grinding. If you want to grind more precisely,

we recommend to work with the direction of grinding. This

applies, for example, to carving tools and knives. Please

note that the grinding process is slowed down if you work

with the direction of rotation.

Please check before each operation whether the surface

of the grinding stone is even. To do so, lower the universal

support onto the stone and turn it manually by 360°. If

required, trim uneven material using the 250 trimming

device.

Upon the time of delivery, the TiGer provides of even

surfaces.

Water Reservoir (Fig. 3, Fig. 4)

Fill the water reservoir with water up to the marking. The

grinding stone becomes saturated with water. Reﬁll water,

if required. Do not grind without water.

Once the grinding process is completed, lower the water

reservoir to prevent the grinding stone from being in the

water for an extended period of time.

Empty the water reservoir regularly. Otherwise, particles of

steel and trimmed stone will accumulate and compress in

the reservoir.

Expert tip: Such precipitations can be avoided if you place

a magnet into the water.

Angle Measurer (Fig. 5)

Measure the angle of the grinding bezel by comparing the

cutting edge to the notches. Then, you set the determined

angle at the device by changing the height of the universal

support. To do so, perform the following steps:

First, clamp the tool into the device and insert the device

on the universal support.

Then, hold the angle measurer with the desired angle at

the tool tip. Now, adjust the height of the universal support

in such a manner that the front end of the angle measurer

straightly borders the grinding stone. Please make sure

that the angle measurer is always in alignment with the

tool tip.

Note: The values indicated on the angle measurer are only

standard values. Of course, you can change these values

according to your requirements.

Grinding (Fig. 6)

Expert tip: New tools still show traces of the production

process. You can substantially increase the lifetime of your

tools if you grind them on both sides of the cutting edge

before the ﬁrst application. You simply grind the back side

in the free-handed mode on the vertical of the grinding

stone, and the front side as follows.

After you have set the angle, insert the tool mounted in

the device on the universal support, turn on the motor,

and start the grinding process. Press the tool evenly onto

the grinding stone near the cutting edge, and move it

crosswise across the stone. Please make sure that at least

half the width of the cutting edge comes into contact with

the grinding stone at any time to avoid damages of the

stone.

To achieve ﬁner grinding results, prepare the stone using

the Stone preparer. Thereby you increase the graining from

250 to approximately 1000. The SP is available as an

accessory from your scheppach dealer.

Sharpening (Fig. 7)

Never sharpen against the direction of grinding! Otherwise,

the tool will cut into the leather!

Impregnate the leather disc using weak machine oil. Then

apply abrasive paste on the leather disc. Turn on the

device, and distribute the abrasive paste by pressing the

ground tool with circular movements on the wheel.

These preparations are sufﬁcient for ﬁve to ten tools. Then,

you start again with a new layer of machine oil, followed by

new abrasive paste. These measures increase the lifetime

of the leather and the quality of your tools.

Expert tip: You can work in the free-handed mode for the

trimming itself. You achieve a more precise result if you

keep the tool in the device in the position in which you

ground the tool.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TIGER 2500 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish, Finnish as an attachment in your email.

The manual is 4.68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach TIGER 2500 Manual

Product: