782083
25
Zoom out
Zoom in
Previous page
1/100
Next page
25
not remove any chips or splinters from the tables while
the machine is running. Work pieces below 250 mm may
not be planed.
Changing the knives (Fig. 11)
• PutthemainswitchofthemachinetoOFFposition.
• Pullthepowersupplyplugfromthesocket.
• Blockthecutterblockguardintheliftedposition.
• Releaseandremovethefourknifeclampingscrews.
• Lifttheknivesandknifesupportfromthecutterblock.
• Removethechipsandanyresinfromthecutterblock
and knife support.
• Placenewknivesintothecutterblockandxthemwith
the rectangle slots in both screw heads. (With these two
screws, height-adjustment of the knife is done.)
• Placetheknifesupportontotheknife.
• Slightlytightenthefourclampingbolts.
• Repeattheseactionsforthesecondknife.
• Thenadjusttheplaner/thicknesserknivesexactlywith
the output table. Use a ruler that you put onto the out-
put table.
• By the two set screws, the knife can be adjusted for
height.
• Byturningthecutterblockandusingtheruler,youcan
see the height adjustment.
• Theknifeisexactlyset,whentherulerismovedbythe
knives not higher than 3 mm.
• After a successful knife setting, all clamping screws
must be tightened (8.4 N/m).
Please mind:
• Sharpplaner/thicknesserknivesguaranteeacleanplan-
ing surface and put less stress on the motor.
• After three grinding actions, a maximum material re-
moval of 3 x 0.05 mm may not be exceeded.
• Theplaner/thicknesserbladesusedonthismachineare
not suitable for rebating and dovetailing.
• Finallylowerthecutterblockguardagainontotheta-
ble. Cover the cutter block and block it with the star grip
screw.
Installation
• Make sure there is sufcient space for handling the
work piece over the whole length without the operator
(or another person) having to stand in line with the work
piece.
• Using bolts, washers and hexagon nuts (not supplied
with the machine), the planer/thicknesser can be bolted
to a work bench.
• Theplaningmachinemustbeboltedontoarm,level
surface.
• The machine may not tilt, and the table must be
aligned.
la machine est en marche. Il est interdit de raboter des
pièces de bois d’une dimension inférieure à 25 cm.
Remplacement des fers de rabot (Fig. 11)
• Mettrel'interrupteuràlaposition«Arrêt».
• Débrancherlaprised’alimentation.
• Bloquerlaprotectiondel'arbrederabotagedanssapo-
sition la plus haute.
• Relâcheretenleverles4visdeserragedelame.
• Enleverlalameetlesupportdel'arbre.
• Enlevercopeauxetrésinedel’arbreetdusupport.
• Mettrelanouvellelamedansl'arbreetlaxerparles
fentes dans les 2 têtes de vis. (Ces 2 vis servent à régler
en hauteur la lame.)
• Mettrelesupportdelamesurlalame.
• Serrerlégèrementles4visdeserrage.
• Répéterlaprocédurepourladeuxièmelame.
• Ensuite,réglerprécisementlahauteurdeslamesenre-
lation à la table d’enlèvement, en utilisant une règle.
• La hauteurdeslames estrégléespar les deux visde
glage.
• Vérierlahauteurdeslamesentournantl’arbre,touten
maintenant la règle sur place.
• Lalamealapositioncorrectesilarègleestavancéepar
les lames pas plus de 3 mm.
• Ensuite,reserrertouteslesvisfermément(8,4N/m).
Faire attention:
• Netravaillezqu'avecdeslamesbienaffûtées.Ellesdé-
chargent le moteur et garantissent une surface lisse.
• Aprèsavoiraffûtéleslamestroisfois,l’enlèvementde
matériel ne doit pas excéder 3 x 0,05 mm.
• Leslamesuséessurcettemachinenesontpasappro-
priées à entailler en queue d’aronde.
• Finalementabaisserlaprotectiondel'arbrederabotage
sur la table, couvrir l'arbre et le serrer avec la vis poi-
gnée-étoile.
Installation
• Vérierqu’ilyaitdelaplacesufsantepourguiderle
bois sur toute sa longueur, sans qu’une personne doit se
trouver dans une ligne avec la pièce à travailler.
• Larabodégaupeutêtrexéesurunétabliàl’aidede
boulons, rondelles et écrous hexagonaux (non livrés).
• Larabogaudoitêtrevisséefermémentàunesurface
solide et lisse.
• Lamachinenedoitpasbasculer,etlestablesdoivent
s'aligner.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SP 85 Spero at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SP 85 Spero in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info