782422
19
Zoom out
Zoom in
Previous page
1/180
Next page
19
Setting of the angular stops to 45° (Fig. 4)
• Forsettingtheangularstopto45°movethecutting
head to the left and adjust the screw (4) with the
Allen key until the 45° position on the scale (3) is
reached.
Adjusting the Fence
• Lowerthecuttingheadandpushinthelockpin.Make
sure the table is in 0 mitre position.
• Placeacombinationsquareagainstthefenceandnext
to the saw blade.
• Ifthebladedoesnotcontactthesquare,loosenthe
screws .
• Adjustthefencesothatthefencehasfullcontactwith
the square. Tighten the screws.
Calibrating of the laser line (fig. 5)
• Inordertocalibratethelaserbeamuseashelf(approx.
200 mm x 300 mm). Mark a right angle line and put
the shelf onto the bearing surface of the table.
• Nowalignthemarkingcentredtothesawbladeand
lock it with the clamping shoe.
• Turnonthelaserusingtheon/offswitchonthebattery
cover.
• Inordertocalibratethelaserline,releasethetwoslot-
ted screws 1. Now move the laser unit until the laser
line matches the marked line.
Attention: You can calibrate the laser line to be running
at the side or in the middle of the cut.
• Tightentheslottedscrewsagainandrecalibratethem
as and when required.
Connecting to the Power Supply
Check that the power supply and outlet used are in ac-
cordance with your mitre saw. Have a look at the rat-
ing plate of the motor or the rating on the mitre saw.
Any changes should always be carried out by a qualified
electrician.
This is a double insulated tool which eliminates the need
for an earthed power supply system.
WARNING! Avoid contact with the terminals on the plug when
installing (removing) the plug to (from) the power supply
outlet. Contact will cause a severe electrical shock.
Using an Extension Lead
The use of any extension lead will cause some loss of
power. To keep this to a minimum and to prevent over-
heating and possible motor burn-out, ask advice from a
qualified electrician to determine the minimum wire size
of the extension lead.
The extension lead should be equipped with an earthed
type plug that fits the power supply outlet at one end,
Réglage des butées d’angle sur 45° (Fig. 4)
• Pourréglerlabutéeà45°,déplacerlatêteporte-scie
vers la gauche et régler la vis (4) à l’aide de la clé Allen
jusqu’à ce que la graduation (3) atteigne la position
45°.
Adjustement du guide
• Abaisserlatêtedecoupeetlabloqueraveclagoupille
de sécurité. S’assurer que le plateau est dans la posi-
tion d’onglet 0.
• Placerl’undesbrasd’uneéquerrecombinéecontrele
guide et l’autre contre la lame de scie.
• Silalamenetouchepasl’équerre,desserrerlesvis.
• Ajusterleguidedefaçonqu’iltouchel’équerretout
au long. Serrer les vis.
Ajustement du rayon laser (Fig. 5)
• Pourajusterlerayonlaser,prendreuneplanche(en-
viron 200 mm x 300 mm). Marquer une ligne à angle
droit et approcher la planche de la surface portante de
la table.
• Centrerlemarquageparrapportàlalamedescieet
serrer à l’aide de la bride de serrage.
• Allumer le laser avec le bouton marche/arrêt sur le
couvercle de la batterie.
• Pourréglerlalignelaser,desserrerlesdeuxvisàtête
fendue 1. Ensuite déplacer l’unité laser jusqu’à ce que
la ligne laser corresponde à la ligne marquée.
à noter: La ligne laser peut être réglée de manière à se
situer sur le côté ou au centre de la découpe.
• Resserrerlesvisàtêtefendueetréajustersibesoin.
Branchement de la scie
S’assurer que le courant et la prise utilisée correspondent
à ce dont la scie a besoin. Voir les spécifications qui fi-
gurent sur la plaque signalétique du moteur ou celles qui
figurent sur la scie. Tout changement doit être effectué
par un électricien qualifié.
Ayant une double épaisseur d’isolement, la scie n’a pas
besoin d’une alimentation mise à la terre.
ATTENTION: Eviter tout contact avec les pointes de la fiche
quand on l’enfiche dans la prise de courant ou qu’on l’en
retire. Tout contact causera un choc électrique dangereux.
Emploi d’une rallonge
L’emploi d’une rallonge entraîne automatiquement une
certaine perte de courant. Pour minimiser cette perte et
empêcher le moteur de s’échauffer et de griller, deman-
der à un électricien qualifié quel calibre minimal de fil
la rallonge doit avoir.
La rallonge doit être munie, à une extrémité, d’une fiche
mâle avec mise à la terre, qui s’enfiche dans la prise de
BA sl 8-10 lxu.indd 19 28.02.11 11:01
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SL 1 0 LXU Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SL 1 0 LXU Woodster in the language / languages: English, German, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info