Manual Scheppach SG7000 (page 85 of 128) (English, German, French, Italian)

781621

Zoom out

Zoom in

1/128

Il collegamento all‘impianto elettrico di un edicio

può anche comportare un feedback della corrente

elettrica dell‘azienda di fornitura nel gruppo elettro-

geno. Quando viene ripristinata l‘alimentazione di

rete, il gruppo elettrogeno può esplodere, bruciar-

si o provocare un incendio dell‘impianto elettrico

dell‘edicio.

Fusibile

Il fusibile scollega automaticamente il gruppo elettro-

geno in caso di corto circuito o in caso di sovraccarico

signicativo del generatore sulla spina. Se il fusibile

è saltato automaticamente in posizione off (g. 1,

n.10), vericare che il gruppo elettrogeno collegato sia

in condizioni perfette e non superi il limite di carico con-

sentito del fusibile prima di spingere di nuovo il fusibile.

Manutenzione

Durante i lavori di manutenzione o di riparazione, il mo-

tore deve sempre essere spento.

Prima di ogni utilizzo

Controllare l‘olio motore

Controllare il ltro dell‘aria

Dopo le prime 25 ore di funzionamento

Sostituire l‘olio motore

Dopo 50 ore

Sostituire l‘olio motore

Pulire la candela di accensione

Pulire il preltro

Pulire il ltro dell‘aria

Dopo 100 ore

Far eseguire questi lavori di manutenzione ad un

tecnico specializzato o ad un‘ofcina specializzata.

Controllare il gioco delle valvole

Pulire il serbatoio di carburante

Controllare la condotta del carburante

LAVORI DI MANUTENZIONE

Cambio dell‘olio, g. 8

Sostituire l’olio motore dopo le prime 25 ore di esercizio,

successivamente ogni 50 ore o ogni tre mesi.

1. Far scaricare l’olio motore con il motore caldo.

2. Lasciare funzionare a caldo il motore.

3. Spegnere il motore.

4. Posizionare un contenitore sufcientemente grande

per raccogliere l’olio usato sotto alla vite di scarico

dell’olio (D).

5. Per scaricare l’olio, rimuovere il tappo di rabbocco

dell’olio (A) e la vite di scarico dell’olio (D).

6. Far scaricare l‘olio

7. Riapplicare la vite di scarico dell‘olio (D) con fascet-

ta di tenuta e stringere.

Connection to the electrical installation of a building

can also cause the electric current of the electricity

supplier to return to the power unit. When the mains

supply is restored, the power unit may explode, burn

or cause a re to break out in the electrical installa-

tion of the building.

Overload switch

The fuse will automatically break the generator with a

short circuit or in the case of a signicant overload of the

generator at the power outlet. Is the fuse automatically

jumped out into position off (Fig. 1, No. 10), check

that the connected electrical appliance is in perfect con-

dition and does not exceed the load limit of the circuit

before you push the fuse.

Maintenance

The engine must always be shut off when carrying out

maintenance tasks or repairs.

Before every use (can be carried out by connois-

seurs)

Check the engine oil

Check the air lter

After the rst 25 hours (can be carried out by con-

noisseurs)

Change the engine oil

After 50 hours (can be carried out by connoisseurs)

Change the engine oil

Clean the spark plugs

Clean the fuel strainer

Clean the air lter

After 100 hours

These maintenance tasks must be carried out by a

specialist or a specialised workshop.

Check the valve clearance

Clean the fuel tank

Clean the fuel line

MAINTENANCE TASKS

Oil change, Fig. 9

Change the engine oil after 25 operating hours, then

after 50 hours or every three months.

1 Drain the engine oil when the engine is hot.

2 Warm the engine up.

3 Switch the engine off.

4 Place a container that is large enough to collect the

used oil under the oil drain screw (D).

5 To drain the oil, remove the oil ller cap (A) and the

oil drain screw (D).

6 Drain the oil

7 Re-attach the oil drain screw (D) with a sealing

washer and tighten.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SG7000 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 8.64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach SG7000 Manual

Product: