Manual Scheppach SD1600V (page 20 of 48) (English, German, French, Italian)

644519

Zoom out

Zoom in

1/48

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

• The necessary tools and small parts for assembling

the saw on a workbench are not supplied with

the saw. However, use equipment of at least the

following size:

1 Saw body

2 Foam rubber base

3 Work bench

4 Flat seal

5 Washer (7 mm)

6 Hexagonal nut (6 mm)

7 Lock nut (6 mm)

8 Hexagon head screws (6 mm)

First of all, drill holes into the seating surface and

then insert the screws.

• A foam rubber base for reduction of noise is

not supplied with the saw either. However, we

expressly recommend that you use such a base to

keep vibration and noise to a minimum. Ideal size

400 x 240 mm.

CHANGING THE SAW BLADES

Warning: Switch off the saw and remove the

mains supply plug before installing saw b!ades

in order to avoid injuries caused by unintentiona!

activation of the saw.

Saw-blade removal, g. 9-12

• Extract the saw-blade by sliding the table’s inlay

up, then unscrew the tightening screw (1).

• First ease the tension by lifting the clamping lever

(Fig. 9) upwards and if necessary turning it anti-

clockwise to further reduce the tension.

• Slightly press the upper arm down (g. 10).

• Then, rst loosen the upper blade clamping screw

(Figure 11, A), and then the lower clamping screw

with an Allen key.

Inserting the saw-blade:

The teeth of the saw blade must always point down-

wards.

• Fix the blade rst in the lower clamp. To x the

blade, securely tighten the blade clamping screw

(Figure 11, A) with an Allen key.

• Press the upper arm of the saw slightly downwards

(Fig. 10) and fasten the other end of the saw blade

in the upper clamp.

• Tighten the blade with the clamping lever (Fig. 12)

by pressing it down again. Check the tension of the

blade. If the tension is too low, increase it by turning

clockwise. First slacken the clamping lever again.

• Insert the table insert.

Saw-blade with pins

Saw blade removal, g. 9,10+12

• To remove the saw blade, lift the table insert

upwards

• Ease the tension with the clamping lever (Fig. 9).

• Remove the saw-blade from the upper and lower

support by slightly pressing the saw´s upper arm

down (g. 10).

Lifting speed 1/min

(electronical)

500 – 1700

Bench diagonal

adjustment left degrees

0 – 45

Weight kg

12,7

Suction connection

piece ø mm

Motor

Electrical motor

230 V/50 Hz

Power consumption P1 W

120

Acoustic pressure level

measured according to EN

ISO 11201

79,9 dB (A)

7. Installation

Setting the saw bench, Fig. 3

Setting the angle scale

• Release the star button and bring the saw bench

(Fig. 3, A) to a right angle (Fig. 3, B) in relation to

the saw blade.

• Use a 90° angle tc measure the right angle between

the blade and the bench. The saw blade be 90° to

the angle.

• Close the star button again when the distance

between the blade and the 90° angle is at a

minimum. The bench should then be at 90° to the

saw blade.

• Release the lock screw (Fig. 3, C) and bring the

indicator to the zero position. Fasten the screw.

Please note: the angle scale is a useful piece of

supplementary equip ment, but should not be used

for precision work. Use scrap wood for saw tests,

adjust the bench if neces sary.

Note: The bench should not be on the motor

block, this can cause undesireable noise.

Horizontal saw bench and diagonal cuts, Fig. 3+4

• The saw bench can be positioned into a 450

diagonal position or be left in the horizontal

position.

• You can read off the approximate slope angle

by using the angle scale located under the work

bench. For more exact adjustment, use scrap wood

for some saw tests; adjust the bench if necessary.

Blade guard assembly and hold-down clamp, Fig.

5+6

• Assemble the workpiece holder (Fig. 5, A) to the

clamp (Fig. 5, B) as shown in the image. This must

be xed rst to the machine with the tommy screw

(Fig. 5, C).

• Secure the blade guard with the screw and nut.

Assembly of dust blower, Fig. 7

Screw the exi-hose into the opening provided and

tighten it hand-tight.

Mounting the saw on a work bench, Fig. 5

• A workbench made from solid wood is betier than

one made of plywood, as interfering vibrations and

noise are more noticeable with plywood.

20 / 48

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SD1600V in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 3,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach SD1600V Manual

Product: