782188
21
Zoom out
Zoom in
Previous page
1/106
Next page
21
Work hints
Basic operation
Ascrollsawisfundamentallya„curvecuttingtool“but
which can also carry out straight and angled edge cuts.
Familiarise yourself with the following important points
priortocommissioningthesaw.
• The saw does not automatically cut wood. You must
feed the wood against the saw blade manually.
• The cutting process occurs on I y while the blade is
moving downwards.
• Feedthewoodslowlyagainstthesawbladeasthesaw
blade teeth are small and cut only while moving down-
wards.
• AlIpersonscarryingoutworkwiththesawrequiretrain-
ing. The saw blade may break easily during this train-
ingtimeIwhiletheoperatorissti1lunfamiliarwiththe
saw.
• Thesawisbestsuitedtorsheetsofwoodlessthan2.5
cm thick.
• Feedthewoodespeciallyslowlyagainstthebladeand
avoid abrupt curves to prevent the saw blade from
breaking, if you wish to cut wood sheets thickerthan
2.5 cm.
• Saw blade teeth blunten over time, saw blades must
bereplaced.Thesawbladesaresufcienttor1/2to2
operatingtimedependinguponthetypeofwood.
• Tryandmakesurethatthesawbladefollowsthegrain
of the wood in order to obtain a clean cut.
• deco 402/decotronic: Thesawspeedmustbereduced
to minimum when cutting precious and nonterrous
metals.
Inside cuts
Warning: Switch off the saw and remove the mains supply
plug before installing saw blades in order to avoid injuries
caused by unintentional activation of the saw.
This saw is suited also to inside cuts cuts not starting at
theedgeoftheworkpiece.Proceedasfollows:
• Drilla6mmholeintheworkpiece.
• Loosenthebladetensionerandreleasethetensionin
the blade.
• Placetheboreholeoverthesawbladeslotinthework
bench.
• Installthesawbladethroughtheholeintheworkpiece
and through the work blade slot, and fasten the blade
to the holders.
• Whenyouhavecompletedtheinsidecut,removethe
saw blade and then remove the workpiece from the
bench.
Indications pour travail
Principes fondamentaux de l‘utillsation
Danslefond,unescieàdécouperestun«outilàdécou-
per des courbes» avec lequel il est cependant possible
d‘entreprendreaussidesdécoupagesd‘anglesdroitsetde
biais. Avant de ne mettre la scie en service, vous devriez
vousfamiliarisezaveclespointssuivants:
• Lascienedécoupepasleboisd‘ellemême.Vousdevez
conduire à la main le bois vers la scie.
• Leprocessusdesciagen‘alieuquependantlemouve-
ment descendant de la lame de scie.
• Introduisez lentement le bois dans la lame de scie,
étantdonnéquelesdentsdelamedesciesontpetites
etnepeuventcouperquedansunmouvementdescen-
dant.
• Toutepersonnequiutiliselascieabesoind‘unappren
tissage. Pendant cette période, tant que I‘utilisateur
n‘estpasencorefamiliariséaveclascie,ilpeutfacile-
ment arriver que des lames se cassent.
• Lascieestadaptéeaumieuxadespanneauxdeboisde
moins de 2,5 cm.
• Si les panneaux que vous souhaitez découper sont
d‘une épaisseur supérieure 25,4 mm, introduisez le
boisparticulièrementlentementdanslalamedescieet
évitezdescourbesabruptespourempécherquelalame
ne se casse.
• Lesdentsdelalamedescies’usentavecletemps.Les
lamesdesciedoiventêtreremplacées.Selonletypede
bois,leslamesdescierestentengénéraltranchantes
pendant1/2à2heuresdeserviceinterrompu.
• Pourobtenirdesdécoupagesexacts,prenezencompte
latendancedelascieàsuivrelamadrureduboispen
dantledecoupage.
Découpages intérieurs
AVERTISSEMENT: Pour éviter des blessures dues à une
miseenmarcheinvolontairedelamachine,éteignezla
scieetretirezlachedecontactavantd‘entreprendrele
montage de lames de scie.
Cettescieestaussiadaptéeàdesdécoupagesintérieurs,
c‘estàdireàdesdécoupagesquinecommencentpasau
borddelapièced‘oeuvre.Procédezpourcefairedela
façon suivante :
• Percezuntroude6mmdanslapièced‘œuvre.
• Relâchezletendeurdelalameetdétendezlalamede
scie.
• Placezletraupercéaudessusdelafentedelalamede
sciedansIatabled‘auvrage.
• Montezlalamedescieàtraversletroudanslapiece
d‘œuvreetatraverslafentedelalamedescie,etxez
lalameauxxations.
• Lorsquevousenavezterminéavecledécoupageinte-
rieur,retirezlalamedescieetenlevezensuitelapiece
d‘œuvredelatable.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SD16 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SD16 Woodster in the language / languages: All languages as an attachment in your email.

The manual is 3.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info