782188
15
Zoom out
Zoom in
Previous page
1/106
Next page
15
ingpressuremayleadtorapiddeteriorationoftheblade
andadecreaseinperformanceintermsofnishand
cuttingprecision.
• Avoidaccidentalstarts:donotpress the start button
whileinsertingtheplugintothesocket.
Putting into operation
Setting the saw bench, Fig. 2
Setting the angle scale
• Releasethestarbutton(1)andbringthesawbench(2)
toarightangle(3)inrelationtothesawblade.
• Usea 90° angletcmeasurethe right angle between
the blade and the bench. The saw blade be 90° to the
angle.
• Closethestarbuttonagainwhenthedistancebetween
the blade and the 90° angle is at a minimum. The
bench should then be at 90° to the saw blade.
• Releasethelockscrewandbringtheindicatortothe
zeroposition.Fastenthescrew.Pleasenote:theangle
scale is a useful piece of supplementary equipment,
butshouldnotbeusedforprecisionwork.Usescrap
wood for saw tests, adjust the bench if neces sary.
Note: The bench should not be on the motor block, this can
cause undesireable noise.
Horizontal saw bench and diagonal cuts, Fig. 2+3
• Thesawbenchcanbepositionedintoa450diagonal
positionorbeleftinthehorizontalposition.
• Youcanreadofftheapproximateslopeanglebyusing
the angle scale located under the work bench. For more
exactadjustment,usescrapwoodforsomesawtests;
adjust the bench if necessary.
forme ainsi que les instructions de service.
Mise en service
Réglage de la table de sciage, Fig. 2
Aménagement de I‘échelle d‘angles
• Ouvrezleboutondeblocage(1)etmettezlatablede
sciageenangledroitparrapportàlalamedescie.
• Utilisezunanglede90°pourmesurerI‘angledroiten-
tre la lame et la table. La lame de scie devrait être
étroitementappuyecontreI‘angleà90°,
• QuandladistanceentrelalameetI‘angleà90°estau
minimum, refermez leboutonde blocage. La table de-
vraitalorsétreà90°parrapportàlalamedescie.
• OuvrezlavisdeblocagedeI‘échelleetmettezI‘indica-
teurenpositionzéro.Serrezlavis.Corrigezensuitela
visdepositionzerosouslatable.Prenezgardes‘ilvous
plait:I‘échelled‘anglesestunepiècesupplémentaire
utile, mais elle ne devrait pas étre utilisée pour des
travauxdeprécision.Utilisezdubois de déchet pour
quelquessciagesd‘essai;réajustezlapositiondelata-
blesinécessaire.
Remarque:la table ne doit pas être appuvêele bloc du moteur.
Ceci risque de provoquer des bruits indêsirables.
Table de sciage horizontale et déoupages de blais, Fig. 2+3
• Latabledesciagepeutêtreinclinéeà45°àgaucheou
laisseéenpositionhorizontale.
• Voustrouverezsouslatabledetravaill‘échelled‘angles
pourlireI‘angled‘inclinaisonapproximatif.
Pourun réglage plus précis, utilisez du boisde dechet
pourquelquessciagesd‘essai;réajustezlapositiondela
tablesinécessaire.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SD16 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SD16 Woodster in the language / languages: All languages as an attachment in your email.

The manual is 3.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info