Manual Scheppach SD-PT120Li (page 11 of 60) (English, German, Dutch, French, Swedish, Norwegian)

782586

Zoom out

Zoom in

1/60

Equipment Fig.1

1. Torque selector

2. Changeover switch

3. ON/OFF switch

4. Battery pack

5. Pushlockbutton

6. Selector switch 1st gear to 2nd gear

7. Quick-change drill chuck

8. LED-light

9. Battery capacity indicator

Startup

Be sure to read the following information

before you use your cordless screwdriver for

the rst time:

1. Charge the battery pack with the charger

supplied. An empty battery pack requires

a charging period of approximately 1

hour.

2. Only ever use sharp drill bits and

screwdriver bits which are suitable for the

purpose and in faultless condition.

3. Always check for concealed electric

cables and gas and water pipes when

drilling and screwing in walls.

Adjusting the torque

The battery-powered drill/screwdriver is equip-

ped with a mechanical torque adjustment fa-

cility. The torque for a specic size of screw is

selected with the set-collar (Fig.1.Pos.1). The

correct torque depends on several factors:

• on the type and hardness of material in

question

• on the type and length screws used

• on the requirements needing to be met by

the screwed joint.

The clutch disengages with a grating sound to

indicate when the set torque is reached.

Important! The tool must be at a standstill

when you set the torque with the setting

ring.

Drilling

For drilling purposes, move the set-collar

to the last step „Drill“. In this setting the slip

clutch is inactive. The maximum torque is

available in drilling mode.

Forward/Reverse switch

(Fig.1.Pos.2)

With the slide switch above the On/Off switch

you can select the direction of rotation of the

batterypowered drill/screwdriver and secure

it against being switched on accidentally. You

can choose between clockwise and anticlock-

wise rotation. To avoid causing damage to the

gearing it is advisable to change the direction

of rotation only when the tool is at a standstill.

The On/Off switch is blocked when the slide

switch is in centre position.

On/Off switch (Fig.1.Pos.3)

Innitely variable speed control is possible

with the On/Off switch. The further you press

the switch, the higher the speed of the battery-

powered drill/screwdriver.

Changing over from 1st gear

to 2nd gear (Fig.1.Pos.6)

You can work at a higher or lower speed de-

pending on the position of the selector switch.

To avoid damaging the gear unit you should

only change over gears when the tool has

stopped.

Screwdriving

We recommend using self-centering screws

(e.g. Torx screws, recessed head screws)

designed for reliable working. Be sure to use

a bit that matches the screw in shape and

size. Set the torque, as described elsewhere

in these operating instructions, to suit the size

of screw.

Maintenance

Cleaning

• Keep all safety devices, air vents and the

motor housing free of dirt and dust as far

as possible. Wipe the equipment with a

clean cloth or blow it with compressed air

at low pressure.

• We recommend that you clean the device

immediately each time you have nished

using it.

• Clean the equipment regularly with a

moist cloth and some soft soap. Do not

use cleaning agents or solvents; these

could attack the plastic parts of the equip-

ment. Ensure that no water can seep into

the device.

Maintenance

• There are no parts inside the equipment

which require additional maintenance.

Disposal and recycling

The unit is supplied in packaging to prevent

its being damaged in transit. This packaging

is raw material and can therefore be reused

or can be returned to the raw material system.

The unit and its accessories are made of

various types of material, such as metal and

plastic. Defective components must be dis-

posed of as special waste. Ask your dealer or

your local council.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SD-PT120Li in the language / languages: English, German, Dutch, French, Swedish, Norwegian as an attachment in your email.

The manual is 3.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach SD-PT120Li Manual

Product: