Manual Scheppach SD-PT120Li (page 10 of 60) (English, German, Dutch, French, Swedish, Norwegian)

782586

Zoom out

Zoom in

1/60

low discharge cycles. Charge the battery

pack frequently.

3. Store the battery pack in a cool place,

ideally at 15°C and charged to at least

40%.

4. Lithium-ion batteries are subject to a

natural ageing process. The battery pack

must be replaced at the latest when its

capacity falls to just 80% of its capacity

when new. Weakened cells in an aged

battery pack are no longer capable of

meeting the high power requirements and

therefore pose a safety risk.

5. Do not throw battery packs into an open

re. There is a risk of explosion!

6. Do not ignite the battery pack or expose

it to re.

7. Do not exhaustively discharge batteries.

Exhaustive discharge will damage the

battery cells. The most common cause of

exhaustive discharge is lengthy storage

or non-use of partly discharged batteries.

Stop working as soon as the performance

of the battery falls noticeably or the elec-

tronic protection system triggers. Place

the battery pack in storage only after it

has been fully charged.

8. Protect batteries and the tool from

overloads. Overloads will quickly result in

overheating and cell damage inside the

battery housing without this overheating

actually being apparent externally.

9. Avoid damage and shocks. Replace

batteries which have been dropped from

a height of more than one meter or which

have been exposed to violent shocks

without delay, even if the housing of the

battery pack appears to be undamaged.

The battery cells inside the battery may

have suff ered serious damage. In this

respect, please also read the waste dis-

posal information.

10. If the battery pack suff ers overloading

and overheating, the integrated protective

cut-off will switch off the equipment for sa-

fety reasons. Important. Do not press the

ON/OFF switch any more if the protective

cut-off has actuated. This may damage

the battery pack.

11. Use only original battery packs. The use

of other batteries may result in injuries,

explosion and a re risk.

Information on chargers and the charging

process

1. Please check the data marked on the

rating plate of the battery charger. Be

sure to connect the battery charger to a

power supply with the voltage marked on

the rating plate. Never connect it to a diff

erent mains voltage.

2. Protect the battery charger and its cable

from damage and sharp edges. Have

damaged cables repaired without delay

by a qualied electrician.

3. Keep the battery charger, batteries and

the cordless tool out of children’s reach.

4. Do not use damaged battery chargers.

5. Do not use the supplied battery charger

to charge other cordless tools.

6. In heavy use the battery pack will become

warm. Allow the battery pack to cool to

room temperature before commencing

with the charging.

7. Do not over-charge batteries. Do not ex-

ceed the maximum charging times. These

charging times only apply to discharged

batteries. Frequent insertion of a charged

or partly charged battery pack will result

in over-charging and cell damage. Do not

leave batteries in the charger for days on

end.

8. Never use or charge batteries if you sus-

pect that the last time they were charged

was more than 12 months previously.

There is a high probability that the battery

pack has already suff ered dangerous

damage (exhaustive discharge).

9. Charging batteries at a temperature

below 10°C will cause chemical damage

to the cell and may cause a re.

10. Do not use batteries which have heated

during the charging process, as the bat-

tery cells may have suff ered dangerous

damage.

11. Do not use batteries which have suff

ered curvature or deformation during the

charging process or which show other

non-typical symptoms (gassing, hissing,

cracking,…)

12. Never fully discharge the battery pack

(recommended depth of discharge max.

80%) A complete discharge of the battery

pack will lead to premature ageing of the

battery cells.

13. Never charge the batteries unsupervised.

Protection from environmental inuences

1. Wear suitable work clothes. Wear safety

goggles.

2. Protect your cordless tool and the battery

charger from moisture and rain. Mois-

ture and rain can cause dangerous cell

damage.

3. Do not use the cordless tool or the battery

charger near vapors and in ammable

liquids.

4. Use the battery charger and cordless

tools only in dry conditions and an ambi-

ent temperature of 10-40°C.

5. Do not keep the battery charger in places

where the temperature is liable to reach

over 40°C. In particular, do not leave the

battery charger in a car that is parked in

the sunshine.

6. Protect batteries from overheating. Over-

loads, over-charging and exposure to di-

rect sunlight will result in overheating and

cell damage. Never charge or work with

batteries which have been overheated –

replace them immediately if possible.

7. Storage of batteries, battery chargers and

cordless tools. Store the charger and your

cordless tool only in dry places with an

ambient temperature of 10-40°C. Store

your lithium-ion battery pack in a cool,

dry place at a temperature of 10-20°C.

Protect them from humidity and direct

sunlight. Only place fully charged batte-

ries in storage (charged at least 40%).

8. Prevent the lithium-ion battery pack from

freezing. Battery packs which were stored

below 0°C for more than 60 minutes must

be disposed of.

9. When handling batteries beware of elec-

trostatic charge: Electrostatic discharges

cause damage of the electronic protec-

tion system and the battery cells. Avoid

electrostatic charging and never touch the

battery poles.

Intended Use m

The cordless drill/screwdriver is designed for

tightening and undoing screws, as well as for

drilling in wood, metal and plastic.

The machine is to be used only for its prescri-

bed purpose. Any other use is deemed to be

a case of misuse. The user / operator and not

the manufacturer will be liable for any damage

or injuries of any kind caused as a result of

this.

Please note that our equipment has not been

designed for use in commercial, trade or

industrial applications. Our warranty will be

voided if the machine is used in commercial,

trade or industrial businesses or for equivalent

purposes.

Remaining risks m

Even if you use this electric power tool

in accordance with instructions, certain

residual risks cannot be rules out. The

following hazards may arise in connection

with the equipment´s construction and

layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protec-

tion is used.

3. Health damage caused by hand-arm

vibrations if the equipment is used over a

prolonged period

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SD-PT120Li in the language / languages: English, German, Dutch, French, Swedish, Norwegian as an attachment in your email.

The manual is 3.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach SD-PT120Li Manual

Product: