782191
33
Zoom out
Zoom in
Previous page
1/36
Next page
33
Troubleshooting table
Warning: In the interests of operational safety, always switch off the saw and remove the mains plug before carrying out
maintenance work.
Fault Possible causes Action
Saw blades break Tension incorrectly set Set the correct tension
Load to great Feed the workpiece more slowly
Incorrect saw blade variety Use the correct saw blades
Workpiece not fed straight Avoid exerting pressure from the side
Motor does not function Mains Gable faulty Change faulty parts
Motor faulty Call customer service. Do not attempt
to repair the motor yourself as this
should be carried out by trained
personnel.
Vibration
NOTE: The saw vibrates slightly
when the motor is running in normal
operation.
Saw incorrectely installed Refer to the instructions given earlier
in this manual for information on
installing the saw
Unsuitable underlay The heavier the work bench is,the
less the vibration. A bench made from
ply wood always vibrates more than
one made from solid wood. Select
the work bench best suited to your
working conditions
The work bench is not screwed down
or is on the motor
Tighten the locking lever
The motor is not secured Securely screw the motor in place
Saw blade swings out
Holders not aligned straight
Holders not aligned Losen the screws with which the
holders are fastenedto the arm.
Align the holders so that they are
perpendicular to each other and
retighten the screws.
Recherche des défauts
Avertissement: Eteignez toujours la scie et retirez la prise du secteur avant d‘entreprendre des travaux de réparation.
Défaut Origine possible Manière de procéder
Les lames se cassent Tension mal réglée Régler la tension convenablement
Charge trop forte Faites avancer la pièce plus lentement
Type de lame incorrect Utiliser des lames convenables
La pièce se met en biais Éviter d'exercer une pression latérale
Le moteur ne marche pas Câble d'alimentation défectueux Remplacer les pièces défectueuses
Moteur défectueux Appeler le service après vente.
N‘essayez pas de réparer le moteur
vous même, ceci doit être effectué par
un spécialiste agréé
Vibrations
REMARQUE: La scie vibre un peu
pendant le fonctionnement.
Scie mal montée Pour le montage de la scie, voir les
indications plus haut dans le manuel
Support incorrect Plus la table est lourde, plus la
vibration est faible. Une table en
aggloméré vibre toujours plus qu‘une
table en bois massif. Choisissez la table
qui convient
Table mal serrée au appuyée contre le
moteur
Tirer le levier de blocage
Moteur mal serré.Fixations non mises
en place
Bien visser le moteur
La lame de scie n‘oscille pas. Se place
de biais
Desserrez les vis avec lesquelles les
fixations sont fixées au bras
Mettre les fixations en position
verticale. Resserrer les vis.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SAC405F Kity at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SAC405F Kity in the language / languages: English, German, French as an attachment in your email.

The manual is 2.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info