782191
21
Zoom out
Zoom in
Previous page
1/36
Next page
21
Montage du protecteur de lame, Fig. 4
Assemblez le protecteur de lame sur le support, comme
I‘indique I‘illustration. Fixez fermement la vis avec un
écrou et une rondelle.
Soulevez la scie par le bras et le socle et posez-Ia sur
le plan de travail.
Familiarisez vous avec les indications d‘utilisation et
les capacités de la scie.
Fixation de la scie sur un établi, Fig. 5
Un établi en bois massif est plus adapté pour utiliser
la scie qu‘un panneau posé sur des tréteaux, les
vibrations et le bruit sont plus présents dans ce cas.
Les outils et le petit matériel de montage nécessaires
pour la fixation sur un établi ne sont pas livrés avec
la scie. Utilisez un équipement correspondant à ce
qui suit :
1. Bâti de la scie
2. Support an caoutchouc mousse
3. Etabli
4. Joint plat
5. Rondelle
6. Ecrou à six pans
7. Contre-écrou
8. Boulon à tête hexagonale
Quantité nécessaire
4 Boulons 6 pans (6 mm) x longueur
4 Rondelles (7 mm)
8 Ecrous à 6 pans (6 mm)
4 Rondelles (7 mm)
Percez des trous de Ø 8 mm dans le support et assem-
blez la machine sur le support en utilisant les boulons
Le support en caoutchouc mousse préconisé ne fait
pas partie de l’ensemble de livraison. Nous recom-
mandons fortement I‘utilisation d‘un tel support pour
maintenir un faible niveau de vibrations et de bruit.
Dimensions idéales de ce support : 400 x 240 mm.
REMPLACEMENT DES LAMES DE SCIE
AVERTISSEMENT: Pour éviter des blessures dues à la mise
en marche non intentionnelle de la scie. arrêtez la scie et
débranchez la fiche du câble d’alimentation avant de com-
mencer le montage de la lame de scie.
A. Lames de scie sans ergots
Utilisez les adaptateurs (fig 6.1)
La longueur est réglée en positionnant les adaptateurs
dans les emplacements du dispositif de mise à longueur
au-dessus du bras de la scie (10)
La lame de scie est fixée avec les vis à six pans creux
des dispositifs.
A 1 Pour enlever la lame de scie, fig. 7+8
Pour enlever la lame de scie, enlevez la lumière
de table en la poussant vers le haut et desserrez la
manette de tensionnement (1).
Abaissez le levier supérieur légèrement vers le bas
fig. (10).
Enlevez la lame de scie en la retirant des supports et
Blade guard assembly, Fig. 4
Install the blade guard to the holder as shown in the
diagram. Secure the screws with a nut and washer.
Lift the saw onto the frame and base and push it onto
the workbench.
Familiarize yourself with the saw operating elements
and features.
Mounting the saw on a work bench, Fig. 5
A workbench made from solid wood is betier than one
made of plywood, as interfering vibrations and noise
are more noticeable with plywood.
The necessary tools and small parts for assembling
the saw on a workbench are not supplied with the saw.
However, use equipment of at least the following size:
1 Saw body
2 Foam rubber base
3 Work bench
4 Flat seal
5 Washer
6 Hexagonal nut
7 Lock nut
8 Hexagonal bolt
Ouantity Description
4 Hexagonal bolts (6mm) 1/4-20 x length
4 Flat seal (7mm) 9/321.0
4 Washers (7mm) 9/321.0.
8 Hexagonal nuts (6 mm) 1/4-20
First of all, drill holes into the seating surface and then
insert the screws.
A foam rubber base for reduction of noise is not
supplied with the saw either. However, we expressly
recommend that you use such a base to keep vibration
and noise to a minimum. Ideal size 400 x 240 mm.
CHANGING THE SAW BLADES
Warning: Switch off the saw and remove the mains supply
plug before installing saw b!ades in order to avoid injuries
caused by unintentiona! activation of the saw.
A. Flat saw-blades
Use the adapter (g. 6.1) with flat saw-blades.
The saw-blade is fixed with Allen screws.
A 1 Saw-blade removal, fig. 7+8
Extract the saw-blade by sliding the table’s inlay up,
then unscrew the tightening screw (1).
Slightly press the upper arm (5) down (g. 10).
Then remove the sawblade by pulling it forward out
of the supports and through the access perforation
in the table.
A 2 Inserting the saw-blade:
Put the saw-blade with the two adapters into the lower
support, the other end into the upper support.
Slightly press the upper arm (5) down (g 10) before
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SAC405F Kity at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SAC405F Kity in the language / languages: English, German, French as an attachment in your email.

The manual is 2.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info