782191

Scheppach SAC405F Kity Manual

19
Zoom out
Zoom in
Previous page
1/36
Next page
19
Montage de la Scie à chantourner, Fig. 1
1 Manette de tensionnement de la lame: pour enlever
la lame de scie et la tendre.
2 Protecteur de lame: protège vos mains de blessures
éventuelles.
3 Pied de biche: maintient la pièce appliquée sur la
table.
4 Soufflette à poussière: évite le dépôt de poussière
sur la pièce , en masquant le trait de découpe.
5 Variateur de vitesse
6 Bouton Marche /Arrêt
7 Graduation de l’inclinaison de la table: vous permet
de lire le degré d‘inclination de la table.
8 Eclairage
9 Flexible d’entraînement équipé d’un mandrin
10 Dispositif de mise à longueur pour les lames sans
ergots
11 Raccordement d’aspiration de poussière
Mise en service
Réglage de la table de sciage, Fig. 2
Réglage de la graduation d’inclinaison de la table
• Desserrez la molette de blocage (1) et placez la table
de sciage à angle droit par rapport à la lame de scie.
• Utilisez une équerre à 90° pour mesurer I‘angle droit
entre la lame et la table. La lame de scie devrait être
appuyée contre I‘équerre.
• Lorsque la distance entre la lame et I‘équerre est au
minimum, resserrez la molette de blocage. La table
devrait alors être alors parfaitement positionnée à 90°
par rapport à la lame de scie.
• Dessserrez la vis de blocage (4) de la graduation et
placez Ie repère en position zéro. Resserrez la vis.
Attention : Ia graduation est un accessoire très utile,
qui ne peut pas être utilisé pour des travaux de
précision sans vérification préalable. Vérifiez avec une
pièce d’essai et réajustez la position de la table si
nécessaire.
Remarque:la table ne doit pas être appuyé contre le bloc
moteur, au risque de provoquer des bruits indésirables.
Table de sciage horizontale et découpes de biais, Fig. 2+3
• La table de sciage peut être inclinée à 45° vers la
gauche ou placée en position horizontale.
• Vous trouverez sous la table de travail une graduation
permettant de lire I’angle d‘inclinaison approximatif.
Pour un réglage plus précis, utilisez une pièce d’essai
pour vérifier l’angle et réajustez la position de la table
si nécessaire.
Scroll Saw Design Features, Fig. 1
1. Clamping screw: for removing the saw blade.
2. Blade guard: protects your hands from injury.
3. Work piece holder
4. Shavings blower: keeps the workpiece area free from
dust.
5. electronical speed switch
6. On/Off switch
7. Angle scale: you can read the angle position of the
table with this scale.
8. Lighting
9. Flexible shaft with drill chuck
10. Setting gauge for saw blades without pin
11. Suction connector
Installation
Setting the saw bench, Fig. 2
Setting the angle scale
• Release the star button (1) and bring the saw bench
(2) to a right angle (3) in relation to the saw blade.
• Use a 90° angle tc measure the right angle between
the blade and the bench. The saw blade be 90° to
the angle.
• Close the star button again when the distance between
the blade and the 90° angle is at a minimum. The
bench should then be at 90° to the saw blade.
• Release the lock screw and bring the indicator to the
zero position. Fasten the screw. Please note: the angle
scale is a useful piece of supplementary equip ment,
but should not be used for precision work. Use scrap
wood for saw tests, adjust the bench if neces sary.
Note: The bench should not be on the motor block, this can
cause undesireable noise.
Horizontal saw bench and diagonal cuts, Fig. 2+3
• The saw bench can be positioned into a 450 diagonal
position or be left in the horizontal position.
• You can read off the approximate slope angle by using
the angle scale located under the work bench. For
more exact adjustment, use scrap wood for some saw
tests; adjust the bench if necessary.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SAC405F Kity at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SAC405F Kity in the language / languages: English, German, French as an attachment in your email.

The manual is 2.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info