782076
17
Zoom out
Zoom in
Previous page
1/156
Next page
17
Remaining hazards
The machine has been built using modern technology in
accordance with recognized safety rules. Some remaining
hazards, however, may still exist.
The rotating planing spindle can cause injuries to fin-
gers and hands if the work piece is incorrectly fed.
Thrown work pieces can lead to injury if the work piece
is not properly secured or fed, such as working without
a limit stop.
Wood chips and sawdust can be health hazards. Be sure
to wear personal protective gear such as safety goggles
and a dust mask. Use a vacuum exhaust system.
Injuries through defective planer/thicknesser blades.
Check the blades regularly for their perfect condition.
Risk of injuries to finger and hands when changing the
planer/thicknesser blades. Wear suitable gloves.
Risk of injuries through the starting planer/thicknesser
blades when switching on the machine.
Injuries caused by electricity through the use of dam-
aged extension cables.
Health hazards through the running tool with long hair
and loose clothes. Wear personal protective gear like a
hairnet and close-fitting clothes.
Even when all safety measures are taken, some remain-
ing hazards which are not yet evident may still exist.
Remaining hazards can be minimized by following the
instructions in "Safety Precautions", “Proper Use", and
in the entire operating instructions.
Setting up
Prepare the location of the machine. Make sure there is
sufficient space to allow safe and trouble-free working.
The machine has been designed to operate in enclosed
rooms. It must be set up in a stable way on a level, firm
ground.
The machine can be fastened to a work bench (fixing ma-
terial not included in the supply extent (Fig. 1).
Transport
For transport, the machine may only be lifted on the base.
Never lift it on the guards, the setting handles or the plan-
er/thicknesser table.
Before transporting, pull the power supply plug.
During transport, the cutter block guard must be set in the
lowest position.
Unpacking the machine
Check the contents of any possible transport damage.
In case of a damage, inform immediately the forwarding
agent. Check the contents for completeness. Inform im-
Risques résiduels
Cette machine est à la pointe de la technique et répond
aux règles de sécurité actuellement en vigueur. an-
moins, certains risques siduels peuvent survenir pen-
dant son fonctionnement.
Risque de blessure aux doigts et aux mains au contact
de l'arbre portelames rotatif à un guidage inappro-
prié de la pièce à travailler.
Blessures au contact de la pièce à travailler projetée en
raison d’un mauvais serrage ou d’un mauvais guidage
- en cas de travail sans butée, par exemple.
Risque pour la santé provenant de la sciure ou des co-
peaux. Il faut impérativement porter des équipements
de protection personnels tels qu’une protection pour les
yeux et un masque contre la poussière. Installer un dis-
positif daspiration.
Blessures par des fers de rabot défectueux. Inspection-
ner régulièrement les fers.
Risque de blessure aux doigts et aux mains lors du
changement de fers. Porter des gants.
Risque de blessure par les fers lors de mettre en mar-
che la machine.
Risque à l’électricilors de l’utilisation de câbles de
raccordement électriques non conformes.
Risque pour la santé en cas de cheveux longs et de
vêtements larges. Porter des vêtements bien seyants et
un filet.
De plus, des risques résiduels invisibles peuvent surve-
nir malgré toutes les précautions prises.
Les risques siduels peuvent être réduits si les «rè-
gles de sécurité» et «l’utilisation conforme aux prescrip-
tions» ainsi que le mode d’emploi sont respectés.
Installation
Préparer le lieu de travail pour la machine. Créer de la
place suffisante pour permettre un travail sans dangers
et sans problèmes. La machine a été construite pour être
utilisée dans des locaux fermés et doit reposer sur un sup-
port stable.
La machine peut être montée sur un établi (pièces de
montage non fournies) (Fig. 1).
Transport
Pour transporter, n’attacher le dispositif de relevage qu’au
bâti, jamais aux dispositifs protecteurs, aux poignées de
réglage ou à la table de dégauchissage.
Pour le transport, débrancher la prise d’alimentation.
Lors du transport, le protecteur de larbre de rabotage doit
se trouver dans la position la plus basse.
Déballage de la machine
Vérifier s la livraison, qu’aucune pièce n’ait été dété-
riorée pendant le transport. En cas de réclamation, infor-
mer aussitôt le livreur. Vérifier que la livraison soit bien
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PT85 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PT85 Woodster in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info