Manual Scheppach PS 1200-55-1 (page 19 of 152) (All languages)

782274

Zoom out

Zoom in

1/152

4 When using a guide rail, it must be fastened with screw

clamps.

5 Make sure the power cable is not placed in the sawing

direction.

Sawing

1 Place the front part of the machine onto the work piece.

2 Switch the machine on using the on/off switch (4).

3 Press the plunge-cut trigger (3).

4 Push the saw downwards to reach the sawing depth.

5 Push the saw forward evenly.

6 After ﬁnishing the sawing cut, switch the machine off

and move the saw blade upwards.

Plunge-cuts, Fig. 9

1 Place the saw onto the work piece.

2 Place the cutting indicator with the rear arrow (A) on

the marked plunge-cut position.

3 Switch the machine on and push the saw downwards

until you reach the set cutting depth.

4 Move the saw forwards until the cutting indication (C)

has reached the marked point.

5 After completion of the plunge-cut, move the saw blade

upwards and switch the saw off.

Cutting with rails (otional)

1 Place the machine in the guide rails. can be readjusted

using the hex driver included in the delivery, when

there is the risk of the adjusting screws releasing by

themselves.

2 Turn on the machine by pressing the on/off switch (4).

3 Press the dip trigger (3).

4 Press the saw downwards to reach the sawing depth.

During ﬁrst use the rubber lip is sawn off and thus

splitter protection is guaranteed up to the saw blade.

5 Push the saw uniformly forwards.

6 Turn off the machine and tilt the saw blade to the top

when the saw cutting is complete.

Sawing with dust suction

Connect the suction hose to the exhaust nozzle - Ø 38

mm (12).

m Electrical connection

The installed electric motor is completely wired ready for

operation.

The customer’s connection to the power supply system, and

any extension cables that may be used, must conform with

local regulations.

Important remark:

The motor is automatically switched off in the event of

an overload. The motor can be switched on again after a

cool ing down period that can vary.

Defective electrical connection cables

Electrical connection cables often suffer insulation dam-

age.

Possible causes are:

• Pinch points when connection cables are run through

window or door gaps.

• Kinks resulting from incorrect attachment or laying of

the connection cable.

• Cuts resulting from running over the connecting cable.

• Insulation damage resulting from forcefully pulling out

of the wall socket.

• Cracks through aging of insulation.

Such defective electrical connection cables must not be

used as the insulation damage makes them extremely

hazardous.

Check electrical connection cables regularly for dam-

age. Make sure the cable is disconnected from the mains

when checking.

Electrical connection cables must comply with the regu-

lations applicable in your country.

Single-phase motor

• The mains voltage must coincide with the voltage spec-

iﬁed on the motor’s rating plate.

• Extension cables up to a length of 25 m must have a

cross-section of 1.5 mm2, and beyond 25 m at least

2.5 mm2.

• The connection to the mains must be protected with a

16 A slow-acting fuse.

Only a qualiﬁed electrician is permitted to connect the

machine and complete repairs on its electrical equip-

ment.

In the event of enquiries please specify the following

data:

• Motor manufacturer

• Type of current of the motor

• Data recorded on the machine’s rating plate

• Data recorded on the switch’s rating plate

If a motor has to be returned, it must always be dis-

patched with the complete driving unit and switch.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PS 1200-55-1 in the language / languages: All languages as an attachment in your email.

The manual is 3.21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach PS 1200-55-1 Manual

Product: