Manual Scheppach PS 1200-55-1 (page 17 of 152) (All languages)

782274

Zoom out

Zoom in

1/152

Do not use any saw blades which do not correspond to

the characteristics described in these operating instruc-

tions. Saw blades may not be brought to a stop by pres-

sure on the machine from the side.

Make sure that the saw blade is tightly assembled and

turns in the correct direction.

m Special Safety Instructions

Safety instructions for circular saws

- Hold the equipment on the insulated handles, when

you undertake work in which the tool being used could

come into contact with hidden electrical wires, or its own

cable. Contact with a live power source can electrify the

metal parts of the tool and lead to an electrical shock.

m Proper use

CE tested machines meet all valid EC machine guidelines as

well as all relevent guidelines for each machine.

• The machine must only be used in technically perfect

con dition in accordance with its designated use and

the in structions set out in the operating manual, and

only by safety-conscious persons who are fully aware of

the risks involved in oerating the machine. Any func-

tional dis orders, especially those affecting the safety of

the machine, sholud terefore be rectiﬁed immediately.

• Any other use exceeds authorization. The manufacturer

is not responsible for any damages resulting from un-

authorized use; risk is the sole responsibility of the

operator.

• The safety, work and maintenance instructions of the

manufacturer as well as the technical data given in

the calibrations and dimensions must be adhered to.

• Relevant accident prevention regulations and other,

gene rally recognized safety-technical rules must also

be adhered to.

• The machine may only be used, maintained, and op-

erated by persons familiar with it and instructed in its

operation and procedures. Arbitrary alterations to the

machine release the manufacturer from all responsi-

bility for any resulting damages.

• The machine may only be used with original accesso-

ries and tools made by the manufacturer.

• The machine may not be operated with sanding belts.

m Remaining hazards

The machine has been built using modern technology in

accor dance with recognized safety rules. Some remaining

hazards, how ever, may still exist.

• The use of incorrect or damaged mains cables can lead

to injuries caused by electricity.

• Even when all safety measures are taken, some re-

maining hazards which are not yet evident may still

be present.

• Remaining hazards can be minimized by following the

instructions in „Safety Precautions“, „Proper Use“ and

in the entire operating manual.

• Do not force the machine unnecessarily: excessive

cutt ing pressure may lead to rapid deterioration of the

slipping to the side. Slippage can lead to a saw blade

jam and a kickback.

d) Do not put the saw on the workbench or the ﬂoor wi-

thout making sure that the protective cover is over the

saw blade. An unprotected, running saw blade can move

the saw against the cutting direction and saw what is in

the way. Check the delay time of the saw.

mAdditional safety instructions for all

sawing with a wedge

a) Use the right wedge for the saw blade that is in use.

The wedge must be thicker than the thickness of the

steel blade but thinner than the width of the teeth.

b) Adjust the wedge as described in the operating inst-

ructions. Incorrect thickness, position or direction can

be the reason that the wedge does not effectively pre-

vent a kickback.

c) Always use a wedge, except when making an inserted

cut. Reassemble the wedge after an inserted cut. The

wedge is in the way when making an inserted cut and

can cause a kickback.

d) In order for the wedge to be effective, it must be in

the sawing gap. For short cuts, a wedge does not work

to prevent kickbacks.

e) Never run the saw with a bent wedge. Even the smal-

lest defect can slow down the closing of the protective

cover.

INSTRUCTIONS FOR ALL SAWS

• Do not use a sanding belt.

• Make sure that the wedge is adjusted so that the di-

stance to the sprocket ring of the saw blade is not

more than 5 mm and that the sprocket ring does not

stick out more than 5 mm above the lower edge of

the wedge.

• Make sure that the dust catching mechanism is cor-

rectly installed, as is described in this manual.

• Wear breathing protection.

• Only those saw blades recommended in the manual

should be used.

• Always wear ear protection.

• Replace the saw blades as described in this manual.

• The maximum cut depth is 55 mm.

If the electrical cable of this tool is damaged it must be

replaced by the manufacturer or the customer service

department or a similarly qualiﬁed specialist in order to

avoid dangers.

FURTHER SPECIAL SAFETY INSTRUCTIONS FOR

CIRCULAR SAWS

a) Only use the recommended saw blades which corre-

spond to EN 847-1.

b) Do not use sanding belts.

c) Only use the manufacturer’s original saw blades with

the number Ø 160 mm, 5500/min, 160 x 20 x 2.0.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PS 1200-55-1 in the language / languages: All languages as an attachment in your email.

The manual is 3.21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach PS 1200-55-1 Manual

Product: