Manual Scheppach PRECISA 6.0 (page 17 of 80) (English, German, Dutch, French, Finnish)

781489

Zoom out

Zoom in

1/80

english 17

• If a second Person is at the circular saw bench to remove

cut workpieces, the machine must be equipped with a

table extension. The second per- son may only stand at the

removal end of the table extension.

• Fit only sharp, crack-free and undistorted circular saw

blades.

• Circular saw blades made of super-high-speed steel must

not be used.

• Safety devices on the machine must not be dismantled or

put out of action.

• The splitting wedge is an important safety feature. The

workpiece is fed through the splitting wedge, which

prevents the cut from closing behind the saw blade and

also prevents the workpiece from kicking back.

• Always lower the protective Cover over the work- piece for

each operation.

• The cowl must stand horizontally above the saw blade

during all working procedures

• Always use the push-stick for longitudinal cutting of narrow

workpieces of less than 120 mm.

• Always stop the machine and disconnect the mains plug

before remedying faults or removing jammed pieces of

wood.

• Replace the blade-slot insert if it is damaged. Disconnect

the mains plug!

• Wear only close-ﬁtting clothes. Remove rings, bracelets

and other jewelry.

• Pay attention to the rotational direction of the motor and

tool - See Electrical Connection.

• Cleaning, changing, calibrating, and setting of the machine

may only be carried out when the motor is switched off.

Pull the power supply plug and wait for the rotating tool to

completely stop.

• Switch the machine off and pull power supply plug when

rectifying any malfunctions

• For all working procedures the machine must be connected

to a scheppach Dust extractor. Observe instructions for proper

use.

• When working on the machine, all safety mecha- nisms and

Covers must be mounted.

• Circular saw blades made from superspeed steel may not

be used.

• The splitting wedge is an important safety feature. The

workpiece is fed through the splitting wedge, which

prevents the cut from closing behind the saw blade and

also prevents the workpiece from kicking back.

• Note the thickness of the splitting wedge - See ﬁgures

stamped into the splitting wedge. The splitting wedge may

not be thinner than the saw blade and not thicker than

cutting joint width.

• Before the machine is put into operation it must be

connected to a dust extractor with a ﬂexible, non-ﬂammable

suction hose. The suction should switch on automatically

when the machine is switched on.

• When leaving the work place, switch the motor off. Pull the

power supply plug.

• Cut off the external power supply of the machine or plant

even if only minor changes of place are envisaged. Properly

reconnect the machine to the supply mains before

recommissioning.

• Connection and repair work on the electrical installation

may be carried out by a qualiﬁed electrician only.

• All protection and safety devices must be replaced after

completing repair and maintenance procedures.

• Pay attention to an sufﬁcient illumination of the

workplace.

• Proof the braking time till the saw blade stopps daily.

It must not be longer than 10 seconds, otherwise do not

continue working.

• Always wear ear protection and protection glasses during

working

• Wear gloves when you change the saw blade

• Power down the machine when you clean it

• Operating conditions: Do not use the machine outside only

inside in closed rooms

• Store conditions: humidity should not be under 90% and

not condensed

• Safe big work pieces of canting

Use only as authorized

• The machine corresponds to the valid EC guideline.

• The scheppach Precisa 6.0 circular sawbench is deﬁned as a

machine in accor- dance with EN 1870-1.

• For transporting the machine within the workshop area use

the scheppach wheel assembly (accessory)

• The working position is to the front of the machine either

to the right or the left sawblade.

• The machining range and surrounding areas of the machine

must be clear of interfering foreign mat- ter to prevent

accidents occurring.

• Workpieces must be completely free of foreign objects, i.e.

nails or screws.

• Before the machine is put into operation it must be

connected to a dust extractor with a ﬂexible, non-ﬂammable

suction hose. The suction should switch on automatically

when the machine is switched On.

• Use the scheppach dust extractor ha 3200 or ha 2600 to

remove matchwood or saw dust. The vacuum support ﬂow

rate must be 20 mls. Subat- mospheric pressure

1200 Pa.

• The scheppach automatic switching unit is avai- lable as a

special accessory.

Typ ALV 2

Art. Nr. 791 0 401 0 230 V150 Hz

Typ ALV 10

Art. Nr. 791 0 4020 400 V150 Hz

The vacuum exhaust unit automatically switches on after a

2-3 second delay after the machine tool is turned On. This

avoids overloading the circuit fuse.

After turning off the machine tool, the vacuum exhaust unit

remains on for an additional 3 - 4 seconds and is then

automatically switched off. Remaining dust is thereby

removed by vacuum exhaust, as required by German

regulations governing hazardous materials. This results in

savings in electricity consumption and reduces noise

levels, as the vacuum exhaust unit is on only during

machine tool operation.

For work in commercial spaces, the scheppach dust

extractor rg 4000 must be used. Do not remove or shut off

vacuum exhaust systems or dust removers while machine

tools are operating.

• The scheppach circular sawbench is designed exclusively

for the machining of wood and materi- als similar to wood.

Only original scheppach tools and accessories may be

used. Use the required sawblade in accordance with the

EN 847-1 norm depending on the type of cut and type of

wood (solid wood, plywood or chipboard). Please observe

the scheppach ,,Special Tool Accessories“ (page 18).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PRECISA 6.0 in the language / languages: English, German, Dutch, French, Finnish as an attachment in your email.

The manual is 7.7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach PRECISA 6.0 Manual

Product: