782583
21
Zoom out
Zoom in
Previous page
1/40
Next page
english 21
Setting into operation
Pleasereadthesafetyinstructionsbeforesettingthesaw
bench into operation.
Allprotectiveandauxiliarydevicesmusthavebeenmount-
ed.Theisreadyforoperationwhenithasbeenconnectec
tothemains.NOTE:Inaccordancewithvalidproductli-
abilitylaws,themanufacturerofthisdeviceshallnotbe
responsiblefordamagetoandfromthisdevicewhichre-
sults from:
• Impropercare
• NoncompliancewiththeOperatingInstructions
• Repairsmadebyunauthorizedpersons
• Theinstallationanduseofanypartswhicharenotorigi-
nal replacement parts.
• Improperuseandapplication
• Failureoftheelectricalsystemasaresultofnoncompli-
ancewiththelegalandapplicableelectricaldirectives
andVDEregulations0100,DIN57113/VDE0113
Sawblade height adjustment – Sawblade angle adjustment, Fig. H
• The height adjustment is made by the rotation of the
wheelonthefrontofthemachine(1).
-SawbladeØ280mm=heightofcutfrom0to90mm
at 90 ° and 0 to 68 mm at 45 °
•Foradjustingthesawbladeanglesettingpulloutthe
handwheelontherightsideofthemachine(2)
- Tilting the blade from 90 ° to 45 °.
-Oncetheadjustmentmade,tightenthegripblocking(3).
Parallel guide, Fig. J, J1, J2
Fine-adjustmen
Fineadjustmentiswiththeadjustingspindle(3)withthe
eccentriclever(1)isblockedandtheeccentriclever(2)
is open.
Stop rail
Position 1 (Fig. J1):Forworkingwithraisedstopbarsur-
face.Thedispayedcutwidthisontheblackdisplayscale
(1).(Higherstopbarsurfacesymbol)
Position 2 (Fig. J2):Forworkingwithloweredstopbarsur-
face. Thedispayedcutwidthisontheblackdisplayscale
(1).(Lowerstopbarsurfacesymbol)
Push-stick and push-grip
Push-stick:Whencuttingnarrowworkpieceslengthwise(i.e.
smallerthan120mm),itisessentialtousethepush-stick.
Push-grip:Whencuttingsmallworkpiecesofspecialform,
it isessential to use the push-grip.
Mitre guide, Fig. G, Fig. G1
Setthemitreguideastherightorleftofthesawblade.
The mitre guide can be directed angle of -45° to +45°.
Refertograduatesector.
Locking fence, Fig. G2(specialaccessory)
The locking fence mounted on the mitre guide is a perfect
complementtomakelengthcutswiththemitreguide.
Changing the sawblades, Fig. F, Fig. F1, Fig. F2
IMPORTANT! Only use sharp, tear-free, unde-formed ‘‘origi-
nalscheppachsawblades’’.
Caution:
When changing the sawblade take out the mains plug!
1 Holding mandre
2 Left-handed hexagonale nut M24
• Takeouttheleft-handtableinlay(Fig.F1)
• Inserttheholdingmandrel(1)intothesawspindlethr-
pough(Fig.F2)theborein theright-handsideofthe
table. For releasing or tightening up the hexagonal nut
M24the sawspindle islocked withthe holdingman-
drel.
• Makenoteoftherunningdirectionofthesawblade.
Riving knife, Fig. F
Releasethescrew(1),insertandclampintherivingknife.
Thedistancebetweenthesawbladeandtherivingknife
must amount to no more than 8 mm and must be checked
eachtimethesawbladeischangedandresetasnecessary.
Therivingknifetipmustneverbesetlowerthantheheight
ofthebaseofthetopmostsawtooth.Asttingtomax.2mm
underthetopmostsawtoothtipisideal.The riving knife
is an irnportant safety device, which guides the workpiece
and prevents the cut pinching and the workpiece being
thrown backwards. Note the riving knife thicknessrefer to the
nurnbers starnped on the riving knife. The riving knife must
not be thinner than the sawblade body and not thicker than
its cutting joint width.
Attention! Close the protection cap
Risk of damage!
Maintenance
Always switch off the motor and disconnect the plug from the
power supply prior to any maintenance and cleaning work.
The following maintenance points should be checked on the
circular saw blench.
• Checkthebelttensionafterapproximatelyoneoperating
hour; retension if necessary. For this purpose open the up-
persidewall.Byuniformadjustmentofthefasteningnuts
on the motor, adjust the necessary belt tension.
Afterthisrstinitialadjustment,checkthebelttensionat
regular intervals.
• Occasionally,oiltherollerchainandmovingparts(height
andangleadjustment).Openthetoprightsidewall.
• Ensurethatthebenchsurfaceisalwaysfreeofresin.
• Thesawprotectionboxmustbeclearedoccasionallyof
woodshavingsandsawdustsothatshavingsdonotjam
whenejected.
• Theheightandangularadjustmentareamaybereduced
byshavingdeposits.Removetheleftbenchinlayandclean
the adjustment area.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Precisa 3.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Precisa 3.0 in the language / languages: English, German, French as an attachment in your email.

The manual is 8.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info