Manual Scheppach Plana 4.0 C (page 16 of 36) (English, German, French)

782088

Zoom out

Zoom in

1/36

14 english

Defective electrical power lines

Often there are isolation defects in electrical power lines.

Possible causes:

• Dents, when the power line was installed through a win-

dow or doorway.

• Cracks resulting from an improper mound or installation

of the power line.

• Cuts from passing around the power line.

• Isolation defects due to pulling out the wall socket.

• Rifts because of changes in isolation. Such defective

electrical power lines must not be used and are, due to

isolation defects life-threatening!

Check the electrical power line regularly for defects. Make

sure that the power line is not connected to the power

supply system during checkup. The power lines must meet

the VDE- and DIN-regulations, as well as the local EVE-

regulations. Use only the power lines with the mark H 07

RN. An identiﬁcation on the cable of the type of line is

mandatory.

Extension cables must be up to 25 m per each 1,5 squared

millimeter section, over 25 m long for a section of at least

2,5 squared millimeters.

The power connection must be supported by a 16 A fuse.

Rotary motor

Line voltage must be 380÷420 V 50 Hz.

Power connection and extension cabling must be up to 5

cores (5adrig) =3 P + N + SL.

Extension cables must cover a section of at least 1,5 mm².

The power connection should optimally be secured by 16 A.

The rotation direction must be checked after connection to

the power or moving the machine, if necessary, the polarity

must be changed.

Connection and repairs of the electrical equipment should

only be done by an electrician.

For inquiries, please have the following information:

• Motor manufacturer; motor type

• Electrical type of the motor

• The machine/type plate information

• Electrical control system information

When sending back the machine, please include the com-

plete propulsion unit with the electrical control system.

Maintenance

Conduct maintenance, repair and cleaning, as well as mal-

function check, only with the unit shut off. Use the on-off

switch to shut down the machine and then disconnect

from the oulet!

All guard and safety instructions must be immediately

mounted after repair and servicing work.

The work table, as well as the thicknessing table must be

kept free of resin. Use long-term lubrication for the storage

of the planer shaft and the tool spindle. In new condi-

tions, warming is part of the design but it goes away after

some time.

Clean the feeder cylinders regularly.

Oil the bearing and shaft with hinges of the sliding bearing

of the feeder cylinders and the adjustment spindle of the

thicknessing table after the ﬁrst 5 hours of operation. After

that, oil every 20 hours of operation.

Check the chain tension. If needed, tighten and oil it.

When tightening the thicknessing table chain, pay atten-

tion to the prallelism of the thicknessing table.

Planer blades

The planer blades at work are beveled and setup correctly,

ready for use.

Only well-sharpened and exactly set planer blades can

guarantee safe operation.

We recommend:

Always keep a spare beveled planer blade ready, in need

of replacement.

Beveling planer blades

Dull planer blades raise the risk of accidents, the work ef-

ﬁciency is no longer guaranteed.

1 Screw for adjustment

2 Tightening screw

3 Planer cutter

4 Tightening wedge shaped part

Do not forget while setting the cutters :

•That there is a risk of injury for the ﬁngers and hands.

•That the tightening surfaces of the cutter block and the

wedge shaped parts must be cleaned

•That the sharp cutters are free of oil

•That the adjustment and positioning of the cutters, of the

cutter holders and of the tightening wedge shaped parts

has to be done according to the drawing ( N°)

•That the cutters, cutter holders and tightening of wedge

shaped parts have to ﬁt as one unit on both sides of the

cutter block (explication )

•That all tightening screws have to be well screwed (8,9

N/m)

Caution !

The indications relative to the ﬁxation of cutters, to the posi-

tion of the cutters, to their thickness, to the minimum ﬁxing

length and to the screwing value have to be followed with

precision.

Adjustment of the cutter blades Fig 17, Fig 17.1

•The adjustment of the cutter blades has been done at the

factory. When needed, you can operate as follows to make

a ﬁne adjustment:

•Adjust one cutter blade after the other.

•Adjust the cutter blade in height in order to touch the two

perfectly planed pieces of wood you have to put right and

left on the outlet surfacing table.

•Set the inlet table at stock removal of 2 mm.

•Turn the cutter block to position the cutter blade at its

highest position.

•While the cutter holder is touching the head of the adjust-

ing screws placed at the bottom of the cavity of the cut-

ter block, release the ﬁxing screws of the cutter with the

wrench (C ) to rise the cutter until it touches both pieces

of wood.

•Adjust exactly , tighten the cutter holder and check the

position of the cutter blades again.

Checking of the position of the cutter blades:

Put a well surfaced piece of wood on the outlet table and

mark its position.

While turning the cutter block in the cutting direction, the

sharp edge of the cutter should take the piece of wood

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Plana 4.0 C in the language / languages: English, German, French as an attachment in your email.

The manual is 5.39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Plana 4.0 C Manual

Product: