Manual Scheppach Plana 4.0 C (page 13 of 36) (English, German, French)

782088

Zoom out

Zoom in

1/36

emission values add up to a total below the underlying

work conditions mentioned in ISO 7904 Appendix A.

Sound power level in dB (Work)

Idle speed LWA = 89 dB (A)

Processing LWA = 98.5 dB (A)

Sound pressure level at the workstation in dB

Idle speed LpAeq = 85.5 dB (A)

Processing LpAeq = 92 dB (A)

Sound power level in dB (Thickness)

Idle speed LWA = 107 dB (A)

Processing LWA = 108 dB (A)

Sound pressure level at the workstation in dB

Idle speed LpAeq = 94 dB (A)

Processing LpAeq = 94.5 dB (A)

The speciﬁed values are emission values and therefore do

not have to represent exact work station values at the same

time. Although there is a correlation between emission and

immission gages, it is not possible to determine reliably,

whether additional precautions are necessary or not. Cur-

rent factors of the work station affect the immission gages,

including the characteristics of the work station, other

sound sources, for example number of machines other ad-

jacent operations. The permissible work values can vary

from country to country. However, the operator should ca-

pacitate the information, in order to make an estimate of

the hazard and risk.

In these operating instructions we‘ve marked the sections that

pertain to your safety with this sign:

General safety instructions

Training of the operator

• Pass on the safety warnings to all people who will work

on the machine.

• The operator must be at least 18 years old. Apprentices

must be at least 16 years old and can only work on the

machine under supervision.

• Persons operating the machine should not be distract-

ed.

• Keep children away from machines connected to the

power system.

• Wear well-ﬁtting clothes. Take off all jewelry, rings and

wristwatches.

• Follow all safety and danger warnings on the machine

and keep them in legible condition.

• Caution while working: risk of injury to ﬁngers and hands

by the rotating cutting tool.

Stability assurance

• During assembly, please make sure that the planing ma-

chine stands ﬁrmly on solid ground.

Utilization in accordance with the regulations

• The planing machine is constructed exclusively from of-

fered tools and supplies for wood processing.

• The machine complies with the valid EG machine guide-

lines.

• The machine is designed for one shift of work, power-on

time S1

• Follow all safety and danger warnings on the machine.

• Keep all safety and danger warnings on the machine

complete and legible.

• When using in an enclosed space, the machine must be

attached to an extraction unit.

• To extract the wood shavings or sawdust, the machine

must be attached to an extraction unit. The velocity of

ﬂow of the connection piece of the extraction unit must

be 20 m/s. Negative pressure 1200 Pa.

• When operating in a commercial area, a deduster must

be employed during extraction.

Do not disconnect or remove the extraction unit or the

deduster while the machine is running.

• Use the machine only when it is in technically sound

conditions, as well as in compliance with the law, with

awareness of safety and danger according with the op-

erating instructions! Eliminate immediately all unneces-

sary distraction that could compromise safety!

• The safety, operation and maintenance instructions of

the manufacturer, as well as the dimensions given in the

technical specs, must be observed.

• The applicable accident prevention regulations and oth-

er technical safety rules of general knowledge must be

observed.

• The machine must be used, maintained or repaired

only by a competent person who can be trusted and is

informed of the dangers. The manufacturer will not be

responsible for damages resulting from arbitrary altera-

tions to the machine.

• The machine should only be used with the original tools

and supplies from the manufacturer.

• All use beyond the instructions counts as noncompli-

ance with the regulations. The manufacturer does not

carry any responsibility for damages resulting from such

use, the operator will bear all risks on his own.

Assembly

Part of scope of delivery:

1 Hook wrench 5,5/7

1 Hex head wrench SW 3

1 Hex head wrench SW 4

1 Hex head wrench SW 6

1 Hex head wrench SW 8

Due to technical reasons, your packed planing machine is not

fully assembled.

The planing machine shouldn‘t be lifted onto the work ta-

ble!

Setup and adjustment, Fig. 1

The machine stands on 4 adjustable rubber cushions.

Balance the unevenness of the ﬂoor. Loosen the lower

hexagon nut using the key and turn the rubber cushions

correspondingly in and out.

Tighten the hexagon nut again. (secure the hexagon nut)

Attention!

Be sure to align the machine by using a level.

If the rubber cushions are displaced, the machine can be

bolted into the boreholes in the ﬂoor.

For utilization with a base frame, dismantle the rubber

cushions and screw on the frame.

Planer fence, Fig. 2, Fig.3

Attach the planer fence to the machine.

Set the position to 90° with the help of a stop angle.

Tighten the release handle

The planer fence is continuously variably pivoting from 90°

english 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Plana 4.0 C in the language / languages: English, German, French as an attachment in your email.

The manual is 5.39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Plana 4.0 C Manual

Product: