757189
20
Zoom out
Zoom in
Previous page
1/56
Next page
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
20 І 56
Maintenance plan
After each workshift: Remove chips and dust from
the device
After 10 hours of operation: When working metal it
is possible for conductive dust to settle in the interior
of the power tool. The total insulation of the power
tool can be impaired. Blow out the interior of the po-
wer tool via the ventilation slots with compressed air.
Cleaning
After each workshift the machine has to be cleaned.
Remove chips etc. with a suitable tool. Do not remove
them by hand (cutting injury!). Remove dust as well.
Notice
The usage of certain solutions containing ingre-
dients damaging metal surfaces as well as the
use of scrubbing agents will damage the machine
surface!
Clean the machine surface with a wet cloth soaked
in a mild solution
Change saw blade and x them in reverse order
Attention: The saw blade continues to rotate after
the machine is switched off.
13. MAINTENANCE
Don’t clean or do maintenance on the machine whi-
le it is still connected to the power supply.
The machine requires little maintenance and contains
little parts that must undergo the operator of a service.
Faults or defects that may affect the safety of the ma-
chine must be rectied immediately.
Notice:
Clean your machine regularly after every usage – it
prolongs the machines lifespan and is a pre-requi-
site for a safe working environment.
Repair jobs shall be performed by respectively
trained professionals only!
Check regularly the condition of the security stickers.
Replace them if required.
Check regularly the condition of the saw band and
the saw band guide.
The good condition and perfect adjustment of the
guiding rollers is essential for a smooth band gui-
dance and a clean cut.
Store the machine in a closed, dry location.
14. Trouble Shooting
Trouble Possible cause Solution
Machine stops or will
not start
On/OFF-switch damaged Check the switch
Saw unplugged Check all power connections
Overload tripped Allow motor to cool and reset by pushing off switch
Fuse blown on circuit breaker tripped Change fuse or reset circuit breake
Cord damaged Change cable
Machine slows down
during working
Experting too much pressure to the
sanding abrasive
Exert less pressure on the work piece
Work piece burns
during the working
process
Wrong saw blade Change saw blade
Too much pressure Reduce pressure
GB
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PL285 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PL285 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info