Manual Scheppach PL285 (page 19 of 56) (English, German, Dutch, French, Italian, Spanish)

757189

Zoom out

Zoom in

1/56

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

19 І 56

Perform all machine settings with the machine

being disconnected from the power supply!

Check before starting work:

• All cables and plugs

• The function of the protective cover (check the

spring!)

The sawing:

• Always use the proper, located in perfect condition

saw blades.

• If possible we recommend that the cutting depth is

set approximately 2 mm deeper than the material

thickness. This should help to ensure

• you achieve a clean cut.

• Do not exert too much pressure to the workpiece.

• Never lay up the saw with open protective cover.

Cutting depth (Fig.2)

• Lift the lock lever to release the cutting depth setting

clamp (7)

• Move indicator to the desired depth of cut

• Lower the lock lever to secure depth of cut

ON/OFF (Fig.3)

• Connect the plug to the power supply (230V):

The power on light (14) is on

• Push ON/OFF switch (5)

• Push the lock-off button (6) forward with the forenger

• The machine is running until releasing the ON/OFF-

switch

Enable cut (Fig.4)

• Let saw blade run to maximum speed

• Pressing the safety lock button (3) unlocks the plunge

cut mechanism at the same time, so that the motor

can be moved downwards

Guide fence (Fig.5)

• Release the lock screw for guide fence (11)

• Set the guide fence (B) in the guide fence slot (10)

• Set a desired width and retighten the lock screw for

the guide fence (11)

Laser (Fig.5)

• On/Off with switch (2)

• Line the laser up with cutting marks on your workpi-

ece

Dust extraction (Fig.7)

• Always use a dust extraction

• Plug the small end of the dust extraction hose (C) with

the dust collector plug (17)

• Connect the bigger end of C with a vacuum device

Selection of saw blades (Fig.8)

• Always use cutting tiles to the diamond wheel (D)

• Use of wood TCT saw blades always the (E).

• Always use plastic and Alumionium the HSS saw

blade (F)

Change the saw blade (Fig.9+10)

• Set cutting depth to maximum

• Press button and hold the spindle lock button (16)

• Use inner hexagon wrench to loosen and remove the

ange screw (8)

• Press the safety lock button (3) to lift up the base

plate (18)

• When cutting aluminium and plastics always use the

app ro priate clamps: all workpieces must be clamped

down rmly.

• Avoid accidental starts: do not press the start button

while inserting the plug into the socket.

• Always use the tools recommended in this manual

to obtain the best results from your plunge cut saw.

• Always keep hands away from the work area when

the ma chine is running; before performing tasks of

any kind release the main switch button located on the

handgrip, thus disconnecting the machine.

11. Technical Data

Dimensions L x W x H mm 410x100x135

Sawblade Ø mm 89

Idle Speed rpm 5500

Cutting depth mm 28.5

Weight kg 2.2

Motor V~/Hz 220-240 / 50

Input W 600

Protection Class II

Laser Class 2

Laser output ≤ 1 mW

Laser module power

supply 2 x LR44 button cell

Noise and vibration

Total vibration values determined in accordance with

EN 61029.

sound pressure level LpA 86,33 dB(A)

uncertainty KpA 3 dB

sound power level LWA 97,33 dB(A)

uncertainty KWA 3 dB

Vibrations sawing of wood ah2,533 m/s²

Vibrations sawing of metal ah2,845 m/s²

Vibrations sawing of concrete ah2,639 m/s²

uncertainty K 1,5 m/s2

The work piece must have a minimum height of 3mm

and a minimum width of 10 mm.

Make sure that the workpiece is always secured with

the clamping device.

12. OPERATION

Operation instructions

Device to be operated in a perfect state only. Inspect

the device visually every time it is to be used. Check

in particular the safety equipment, electrical controls,

electric cables and screwed connection for damage

and if tightened properly. Replace any damaged parts

before operating the device.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PL285 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach PL285 Manual

Product: