782513
60
Zoom out
Zoom in
Previous page
1/84
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
60 | GB
k) Plan your work. Every time you change the bevel or mitre an-
gle setting, make sure the adjustable fence is set correctly to
support the workpiece and will not interfere with the blade or
the guarding system. Without turning the tool “ON” and with no
workpiece on the table, move the saw blade through a complete sim-
ulated cut to assure there will be no interference or danger of cutting
the fence.
l) Provide adequate support such as table extensions, saw hors-
es, etc. for a workpiece that is wider or longer than the table
top. Workpieces longer or wider than the mitre saw table can tip if not
securely supported. If the cut-o󰀨 piece or workpiece tips, it can lift the
lower guard or be thrown by the spinning blade.
m) Do not use another person as a substitute for a table extension
or as additional support. Unstable support for the workpiece can
cause the blade to bind or the workpiece to shift during the cutting
operation pulling you and the helper into the spinning blade.
n) The cut-o󰀨 piece must not be jammed or pressed by any means
against the spinning saw blade. If conned, i.e. using length stops,
the cut-o󰀨 piece could get wedged against the blade and thrown vi-
olently.
o) Always use a clamp or a xture designed to properly support
round material such as rods or tubing. Rods have a tendency to
roll while being cut, causing the blade to “bite” and pull the work with
your hand into the blade.
p) Let the blade reach full speed before contacting the workpiece.
This will reduce the risk of the workpiece being thrown.
q) If the workpiece or blade becomes jammed, turn the mitre saw
o󰀨. Wait for all moving parts to stop and disconnect the plug
from the power source and/or remove the battery pack. Then
work to free the jammed material. Continued sawing with a jammed
workpiece could cause loss of control or damage to the mitre saw.
r) After nishing the cut, release the switch, hold the saw head
down and wait for the blade to stop before removing the cut-o󰀨
piece. Reaching with your hand near the coasting blade is dangerous.
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach MST216 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MST216 in the language / languages: English, German as an attachment in your email.

The manual is 5.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info