782297
13
Zoom out
Zoom in
Previous page
1/152
Next page
13
• Useonlysawbladesrecommendedbythemanufacturer
according to EN847-1.
• Connect your mitre saw to a dust collecting device
when sawing.
• Select saw blades in relation to the material to be
cut.
• Checkthemaximumdepthofcut.
• Whensawinglongworkpieces,alwaysuseextension
wings to provide better support, and use clamps or
other clamping devices.
• Wearearprotection.
WARNING! Noise can be a health hazard. When the noise
level exceeds 85dB(A), be sure to wear ear protection.
Additional safety instructions for laser light
The laser light and laser radiation used in this system
comply with class 1 and a maximum performance of 390
µW and 650 nm wave length. Normally laser does not
represent an optical danger, although staring into the
beam can cause flash blinding.
Warning: Do not look directly into the laser beam, since
this could represent a risk. Please observe the following
safety instructions:
• Thelasermayonlybeusedandmaintainedinaccord-
ance with the instructions of the manufacturer.
• Onlypointthebeamontotheworkpiece,andneverat
a person or another object.
• Thelaserbeammustnot deliberatelybepointedat
persons. It must not be pointed into the eyes of a
person for more than 0.25 seconds.
• Alwaysmakesurethatthelaserbeamisdirectedonto
a robust work piece without a reflecting surface. That
means that timber and materials with a rough surface
are acceptable. Shiny, reflecting plates or similar ma-
terials are not suitable for laser, since the reflecting
surface could return the beam to the operator.
• Donotexchangethelaserlightunitforanothertype.
Repairs have to be conducted by the manufacturer or
an authorised specialised company.
Caution: You must only apply the regulation and adjust-
ment tools and methods described in this manual. Non-
observance can lead to dangerous radiation.
m Proper use
CE tested machines meet all valid EC machine guidelines as
well as all relevent guidelines for each machine.
• Themachinemustonlybeusedintechnicallyperfect
con dition in accordance with its designated use and the
in structions set out in the operating manual, and only
by safety-conscious persons who are fully aware of the
risks involved in oerating the machine. Any functional
que le bois ou des matériaux semblables.
• N’utiliserqueleslamesdescierecommandéesparle
fabricant (accordant au règlement EN847-1).
• Quandonutiliselascie,larelieràuncollecteurde
poussière.
• Choisirlalamedescieenfonctiondumatériauàcou-
per.
• Vérierlaprofondeurmaximaledecoupe.
• Toujoursutiliserdesrallongesdeplateaupourscierde
longues pièces, afin de mieux les soutenir, et utiliser
des serre-joints ou d’autres dispositifs de serrage.
• Porterdesprotecteursd’oreille.
ATTENTION! Le bruit peut constituer un risque pour la santé.
Veiller à porter des protecteurs d’oreille quand le niveau de
bruit dépasse 85 dB(A).
Avertissement supplémentaires sur la lumière Laser
La lumière et le rayon Laser utilisé dans ce système
correspondent à la classe 1 et ont une puissance maxi-
male de 390 µW et une longueur d’onde de 650 nm. Ce
genre de Laser ne représente généralement pas de dan-
ger, cependant fixer ce rayon peut provoquer une cécité
momentanée.
Avertissement : Ne regardez pas directement le rayon
Laser, car ceci pourrait être dangereux. Respectez les
consignes de sécurité suivantes :
• LeLasernedoitêtreutiliséetentretenuqu’enrespec-
tant les prescriptions du constructeur.
• Dirigez le rayon uniquement sur la pièce usinée et
jamais vers une personne ou un autre objet.
• Le rayon Laser ne doit pas être intentionnellement
dirigé vers des personnes. Il ne doit jamais être dirigé
vers les yeux d’une personne pendant plus de 0.25
sec.
• Assurez-vousquelerayonLasersoitdirigéversune
surface solide non réfléchissante, c. à d.: du bois ou
d’autres matériaux ayant une surface rugueuse sont
acceptables. Des tôles brillantes, réfléchissantes ou
des matériaux similaires ne conviennent pas au Laser
car la surface réfléchissante pourrait renvoyer le rayon
vers l’utilisateur.
• Neremplacezpasl’unitéLaserparuneautred’untype
différent. Les réparations doivent être effectuées par
le constructeur ou une entreprise spécialisée.
Attention: Vous ne devez utiliser que les outils et procé-
dures de réglage décrits dans ce manuel. Le non respect
peut provoquer un rayonnement dangereux.
m Utilisation conforme
Les machines contrôlées CE sont conformes aux directives de
l’U.E. en vigueur concernant les machines ainsi qu’à toutes
les directives applicables à la machine.
• Utiliserlamachine/installationuniquementlorsqu’elle
est en parfait état du point de vue technique et confor-
mément à son emploi prévu en observant les instruc-
tions de service, en tenant compte de la sécurité et en
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach MSS 8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MSS 8 in the language / languages: English, German, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info