Manual Scheppach LS40P Woodster (page 17 of 32) (English, German, French)

782006

Zoom out

Zoom in

1/32

17GB

8 Use only attachments and accessories approved

by the manufacturer. Failure to do so can result

in personal injury.

9 Maintain the machine. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the ma-

chine’s operation. If damaged, have the machine

repaired before use. Many accidents are caused

by poorly maintained equipment.

10 Keep the engine and mufer free of grass,

leaves, excessive grease or carbon build up to

reduce the chance of a re hazard.

11 Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

12 Never douse or squirt the unit with water or any

other liquid. Keep handles dry, clean and free

from debris. Clean after each use.

13 Observe proper disposal laws and regulations for

gas, oil, etc. to protect the environment.

14 Store idle machine out of the reach of children

and do not allow persons unfamiliar with the ma-

chine or these instructions to operate it. Machine

is dangerous in the hands of untrained users.

Instructions for maintenance

Before cleaning, repair, inspecting, or adjusting, shut

off the engine and make certain all moving parts have

stopped. Disconnect the spark plug wire, and keep the

wire away from the plug to prevent accidental starting.

Have your machine serviced by qualied repair person-

nel using only identical replacement parts. This will en-

sure that the safety of the machine maintained.

Technical data

Engine type 1-cylinder; 4 - stroke

Displaycement 118 cm³

Max. engine output 2,2 kw

Working speed 3600 rpm

Fuel unleaded fuel

Tank capacity 2,5 l

Engine oil 10W 30 / SAE 30

Tank capacity /oil 0.6 L

spark plug LG F6TC

Depth setting +5 / -15

Working width 400 mm

Number of blades 18

Blade diameter 160 mm

Collection bag capacity 45L

Weight 31 kg

Subject to technical changes!

3 Keep grounded conductive objects, such as

tools, away from exposed, live electrical parts

and connections to avoid sparking or arcing.

These events could ignite fumes or vapors.

4 Always stop the engine and allow it to cool before

lling the fuel tank. Never remove the cap of the

fuel tank or add fuel while the engine is running

or when the engine is hot. Do not operate the ma-

chine with known leaks in the fuel system.

5 Loose the fuel tank cap slowly to relieve any

pressure in the tank.

6 Never over ll fuel tank. Fill tank to no more than

12.5mm (1/2” below the bottom of the ller neck

to provide space for expansion as the heat of the

engine can cause fuel to expand).

7 Replace all fuel tank and container caps securely

and wipe up spilled fuel. Never operate the unit

without the fuel cap securely in place.

8 Avoid creating a source of ignition for spilled fuel.

If fuel is spilled, do not attempt to start the en-

gine but move the machine away from the area of

spillage and avoid creating any source of ignition

until fuel vapors have dissipated.

9 Store fuel in containers specically designed and

approved for this purpose.

10 Store fuel in a cool, well-ventilated area, safely

away from sparks, open ames or other sources

of ignition.

11 Never store fuel or machine with fuel in the tank

inside a building where fumes may reach a spark,

open ame, or other sources of ignition, such as

a water heater, furnace, clothes dryer and the

like. Allow the engine to cool before storing in

any enclosure.

Instructions for use and maintenance of the

machine

1 Never pick up or carry a machine while the en-

gine is running.

2 Do not force the machine. Use the correct ma-

chine for your application. The correct machine

will do the job better and safer at the rate for

which it was designed.

3 Do not change the engine governor settings GB

or over-speed the engine. The governor controls

the maximum safe operating speed of the engine.

4 Do not run the engine at a high speed when you

are not tilling.

5 Do not put hands or feet near rotating parts

6 Avoid contact with hot fuel, oil, exhaust fumes

and hot surfaces. Do not touch the engine or

mufer. These parts get extremely hot from op-

eration. They remain hot for a short time after you

turn off the unit. Allow the engine to cool before

doing maintenance or making adjustments.

7 If the machine should start to make an unusual

noise or vibration, immediately shut off the en-

gine, disconnect the spark plug wire, and check

for the cause. Unusual noise or vibration is gen-

erally warning of trouble.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach LS40P Woodster in the language / languages: English, German, French as an attachment in your email.

The manual is 3.8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach LS40P Woodster Manual

Product: