781932
13
Zoom out
Zoom in
Previous page
1/83
Next page
13
position. Use the hand grip and pull gently while the ma-
chine stands on its wheels.
Your Woodster machine can be stored or transported un-
der ambient temperatures between -20° C and +60° C at
a max. humidity of 80 %.
Assembly
For technical reasons of packaging, the supporting leg (6)
and the handle (5) must be fitted by the customer.
• Supportingleg–2hexagonboltsM6x16withnut
• Handle–2hexagonsocketscrewsM6x16withnut
Place the device horizontally on the floor, and put the
Styropor pad of the packaging underneath the splitting
wedge side.
Setup
Prepare the workplace where the machine is to be placed.
Ensure sufficient room to allow safe work without mal-
functions.
The machine is designed to operate on a level surface and
must be placed securely on firm, level ground.
Please make sure your Woodster machine is placed firmly
on stable plain ground.
m Electrical connections
Regularly check the electrical connection lines for dam-
ages. Please make sure that the connection lines are
disconnected from the mains supply during the check.
Electrical connection lines must meet the applicable VDE
and DIN regulations and the provisions of the local power
supply company. Only use connection lines labeled with
H07RN. The labeling of the connection cable with the
type specification is required.
Damaged electrical connections
Often, insulation damages occur on electrical connection
lines.
The possible causes are:
• Dragmarksifconnectionlinesareledthroughwindow
or door clearances.
• Kinksduetoimproperattachmentorroutingofthecon-
nection line.
• Cutscausedbyrunningovertheconnectionline.
• Insulationdamagescaused by pulling the connection
line out of the wall socket.
• Fissurescausedbytheagingoftheinsulation.
Such defective electrical connection lines must not be used
and are, due to the insulation damages, life threatening!
Single phase motor 230 V/50 Hz
• Thesupplyvoltagemustbe220÷240V/50Hz.
• Themainsconnectionandextensioncablemusthave3
wires = P+N+SL.–(1/N/PE).
• Extension lines up to a length of 25 m must have a
minimum cross section of 1.5 mm², lines with a length
La machine peut être transportée en position inclinée sur
les roues. Utiliser la poignée de manutention, soulever
et tirer.
Conditions de stockage : emplacement sec et recouvert
d’un toit, humidité maximale de l’air 80 %, températures
entre -20°C et +60°C.
Montage
Pour des raisons techniques d’emballage, il faut que le
client monte lui-même le pied de support (6) et la poi-
gnée (5).
• Pieddesupport–2boulonshexagonauxM6x16avec
écrou
• Poignée – 2 boulons à 6 pans creux M6 x 16 avec
écrou
Mettre l’appareil sur un plan horizontal et le caler par le
côtéducoinàfendreàl’aidedurembourragedepolysty-
rène expansé de l’emballage.
Mise en place
Veillez à ce que votre machine soit placée sur un sol plat
et stable et qu’elle soit équipée d’un éclairage suffisant.
Veillez à ce qu’il y ait suffisamment d’espace pour garantir
un travail sûr et sans défaut avec la machine.
m Branchement électrique
Vérifier régulièrement l‘état des lignes de branchement
électrique. Débrancher d‘abord le cordon d‘alimentation!
Les lignes de branchement électrique doivent correspon-
dre aux prescriptions VDE et DIN correspondantes. Uti-
liser uniquement des lignes de branchement électrique
avec la caractérisation H 07 RN.
Une inscription du type sur le câble de branchement est
obligatoire.
Lignes de branchement électrique défectueuses
L’isolement des lignes de branchement électrique est sou-
vent endommagé.
Causes possibles :
• Empreinteslorsqueleslignesdebranchementsontpo-
sées à travers des fentes de fenêtre ou de porte.
• Plissuiteàunexationouuneposeinadéquatedela
ligne de branchement.
• Coupuressuiteàl’écrasementdelalignedebranche-
ment.
• Dommages d‘isolement suite à un arrachement pour
sortir la ligne de branchement de la prise de courant
murale.
• Fissuressuiteauvieillissementdel’isolation.
Il est interdit d’utiliser de telles lignes de branchement élec-
trique endommagées. Et elles présentent un danger de mort à
cause des dommages sur l’isolement.
Moteur à courant alternatif
• Latensiondesecteurdoitêtrede220–240V/50Hz.
• Lecâbledebranchementausecteuretlarallongedoi-
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach LH52 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach LH52 Woodster in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3.78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info