781932
11
Zoom out
Zoom in
Previous page
1/83
Next page
11
Proper Use
• ThemachinemeetsthecurrentlyvalidEUmachinedi-
rective.
• Thehydrauliclogsplitterisdesignedonlyforwoodina
horizontal position. Wood may only be split while hori-
zontal and in the direction of the grain. Dimensions of
wood to be split: maximal 52 cm.
• Neversplitwoodagainstthegrainorwhileinanupright
position.
• Themanufacturer’ssafety,operationandmaintenance
instructions as well as the technical data given in the
calibrations and dimensions must be adhered to.
• Relevant accident prevention regulations and other
generally recognized safety and technical rules must
also be adhered to.
• Themachinemayonlybeused,maintainedorrepaired
by trained persons who are familiar with the machine
and have been informed about the dangers. Unauthor-
ized modifications of the machine exclude a liability of
the manufacturer for damages resulting from the modi-
fications.
• Any other use is considered to be not intended. The
manufacturer excludes any liability for resulting dam-
ages, the risk is exclusively borne by the user.
m Remaining hazards
The machine has been built using modern technology and
in accordance with recognized safety rules.
Some hazards, however, may still remain.
• Thesplittingtoolposesadangerofinjurytongersand
hands by improper feeding or placement of wood.
• Danger of injury from thrown wood due to improper
holding or feeding.
• Theuseofincorrectordamagedmainscablescanlead
to elctrical injuries.
• Minimize remaining hazards by following the instruc-
tions in ”Safety Rules”, ”Use only as authorized” and in
the entire operating manual.
Transport
Transport fork lift/lifting carrier:
Upon dispatch, the machine is tightly mounted to a palette
with 4 screws. Remove the screws with a fork wrench.
To remove the machine from the palette, two persons will
be required.
The machine may be transported while held in a diagonal
Utilisation conforme
• LamachineestconformeàladirectivemachinesCEE
en vigueur.
• Lafendeuseàboishydrauliqueestuniquementdesti-
née à l‘utilisation en position horizontale. Le bois doit
uniquement être fendu à l‘horizontale et dans le sens
des fibres. La taille des morceaux de bois ne doit pas
être supérieure à 52 cm.
• Nejamaisfendreleboisàlaverticaleoucontrelesens
des fibres!
• Lesconsignesde sécurité,ainsiquelesprescriptions
pour le travail et la maintenance, fournies par le fa-
bricant doivent être respectées au même titre que les
dimensions indiquées dans les caractéristiques techni-
ques.
• Lesconsignescorrespondantespourlapréventiondes
accidents et les autres réglementations généralement
reconnues doivent être respectées.
• Seules des personnes compétentes ayant été initiées
et informées sur les dangers possibles ont le droit de
manier, d’entretenir ou de réparer la machine. Des mo-
difications sur la machine effectuées sans autorisation
entraînent une exclusion de la responsabilité du fabri-
cant pour tous dangers éventuels en résultant.
• Lamachinenedoitêtreutiliséequ’avecdesaccessoi-
res et des outils d’origine du fabricant.
• Touteutilisationautrequecellespéciéeestconsidé-
rée comme non conforme. Le fabricant ne peut être
tenu responsable pour d’éventuels dommages résultant
d’une telle utilisation, seul l’exploitant en est responsa-
ble.
m Risques résiduels
La machine est construite selon l’état actuel de la techni-
que et conformément aux réglementations reconnues en
matière de sécurité. Le travail avec la machine peut tou-
tefois présenter des risques résiduels.
• Encasde guidageoud‘appuiincorrectsdubois,ris-
que de blessures des doigts ou des mains par l‘outil de
fente.
• Encasdeguidageoud‘appuiincorrect,risquedebles-
sure dû à la projection de la pièce à usiner.
• Lecourant présente unrisqueen cas d‘utilisationde
lignes de branchement électrique non-conformes.
• Desrisquesrésiduelsnonapparentssonttoutefoisen-
core possibles malgré toutes les mesures prises.
• Ilestpossiblederéduirelesrisquesrésiduelsenres-
pectant les „Consignes de sécurité“ et „l‘Utilisation con-
forme“ ainsi que les instructions de service.
Transport
Transport au moyen d’un chariot à fourche/chariot élévateur:
Pour l’expédition, la machine est bien fixée sur une pa-
lette au moyen de sangles. La machine est protégée par
un carton.
Au minimum 2 personnes doivent retirer la machine du
carton.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach LH52 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach LH52 Woodster in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3.78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info