Manual Scheppach KSB56 - Woodster (page 44 of 76) (English, German, French)

782040

Zoom out

Zoom in

1/76

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

44 GB

m NOTE

Make sure that there is always enough oil in the tank be-

cause chain lubrication is always on.

Automatic chain lubrication - Settings possible!

8. Operation

Start the appliance (Fig.10-13)

m CAUTION!: Before you start the engine, make

sure that the chain isn’t touching anything and the

chain brake is activated before each start.

1. Set the power switch (11) to position „ON“. (Fig.10/

Pos.11a)

2. Pull the hoke lever (7) out completely until it locks

in place.

3. Press the fuel pump ball (6) 10 times (g. 2)

m NOTE

When restarting immediately after stopping the engine,

do not pull out the CHOKE (7).

4. Press the front handle (3) forward to activate the

chain brake

5. Place the saw on a rm, level surface. Hold the saw

rmly with the foot as indicated. Quickly pull the start-

er (13) 2 times. Pay attention to the running chain!

6. Once the engine has started, press the throttle trig-

ger lock (8) and the throttle lever (10) so that the

CHOKE knob (7) clicks into place again.

7. Pull the front handle (3) backwards to release the

chain brake.

8. Let the engine warm up, controlling the throttle set-

ting (10) and letting the chain run briey.

Never start or operate the chainsaw if the chain and the

chain brake lever or the front hand guard have not been

properly installed. In addition, always start with the chain

brake active. Proceed as follows for this:

• Hold the chain saw by the front handle (4).

• Press the front hand guard (3) forward to position (3b).

Press the pedal, the chain should not move.

• Pull the front handle (3) back to position (3a). Press

the pedal, the chain should move.

Stopping the motor (Fig.10)

1. Release the throttle lever and wait until the engine is

idling.

2. Set the power switch to „Stop (0)“ to stop the motor.

(Fig.10/Pos.11b)

m NOTE

To stop the engine in an emergency, activate the chain

brake and set the ON / OFF switch to „Stop“.

9. Cleaning

m WARNING

Disconnect the spark plug boot before doing any clean-

ing and maintenance work. (Fig. 19)

Cleaning

• Keep all safety devices, air vents and the motor-

housing free of dirt and dust as far as possible.Wipe

the equipment with a clean cloth or blow itwith com-

pressed air at low pressure. ATTENTION! Wear safe-

ty glasses!

• We recommend that you clean the device immediately

each time you have nished using it.

• Clean the equipment regularly with a moist cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these could attack the plastic parts of the equip-

ment. Ensure that no water can seep into the device.

10. Maintenance

Air lter (Fig.16-18)

• Clean the air lter (H) after each use.

• Unscrew the air lter mounting nut (Fig.18/Pos.6) and

remove the cover. (see Fig.16)

• Remove the air lter (H).

• Open the air lter with a screwdriver.

• Clean the air lter. Wash the lter in clean, warm,

soapy water. Let the air dry completely.

• Insert the air lter. Put on the cover of the engine / air

lter. Make sure the cover is installed correctly (S-V).

Tighten the screw that secures the cover. (see Fig.16)

m NOTE

It is advisable to keep a stock of spare lters.

Oil supply opening (Fig.20)

• Check the oil supply opening (K) after each use.

• Dissemble the bar.

• Check the oil outlet (K) for obstructions.

Guide bar (Fig.23-24)

• Clean the bar after each use.

• Remove the bar from the machine.

• Remove sawdust from the bar and the oil channel

(Fig.23/Pos.1).

• Lubricate the teeth (Fig.24/Pos.2/3) through the oiling

hole with an oil syringe.

Cylinder ns (Fig.20)

• Clean the cylinder ns (M) after each use. To do this,

use compressed air at low pressure or use a brush.

ATTENTION! Wear safety glasses!

• Dust and dirt between the ns on the cylinder may

cause the machine to overheat.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KSB56 - Woodster in the language / languages: English, German, French as an attachment in your email.

The manual is 5.79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach KSB56 - Woodster Manual

Product: