782080
51
Zoom out
Zoom in
Previous page
1/80
Next page
DGB
50
7. BENUTZUNG DER MASCHINE
i. Dickenhobeln
1. Dickenhobeln der zweiten Fläche (40)
7. PUTTING THE MACHINE INTO OPERATION
i. Thicknessing
1. Thicknessing the second surface (40)
- Entfernen Sie den Hobelwellenschutz (G) oder lassen Sie
ihn einfach voll das Maximum gleiten und arretieren Sie ihn.
(39)
- Kippen Sie den Auswurfschutz (E) und montieren Sie den
Stutzen (F).
- Kuppeln Sie den Antriebshebel für die Bretter (Y) ein. (39)
Wichtig : Vor der Arbeit, überprüfen Sie das keine Äste oder
Metalleinsätze vorhanden sind, um einen möglichen gefähr-
lichen Abwurf zu vermeiden. Prüfen Sie auch, dass das Holz
nicht zu sehr gewölbt ist.
- Stellen Sie die Höhe des Dickentisches ein.
(siehe «Höheneinstellung des Dickenstisches»).
- Legen Sie die bereits gehobelte Fläche aud den Dicken-
tisch (D). Stützen Sie gut ab, um einen Absatz zu vermeiden.
- Führen Sie das Brett so weit ein, bis es von den Einzugsrol-
len (Z) erfasst wird.
- Lassen Sie das Brett durchlaufen, ohne zu schieben.
- Wiederholen Sie den Vorgang, bis Sie eine gut gehobelte
Oberfläche erhalten.
- Stützen Sie das brett am Ende des Durchgangs ab, damit
das Werkzeug keinen Absatz erzeugen kann. (41)
Wichtig : ein Absatz von 1/10 mm kann akzeptiert werden.
(siehe Detail) (41).
- Remove the cutter block guard (G) or let it simply glide at
the maximum, and lock it. (39)
- Tilt the ejection guard (E) and mount the suction connection
(F).
- Engage the drive lever for the boards (Y). (39)
Important : before starting make sure that there are no knots
or metal inclusions to avoid dangerous projections. The work
must not be too much curved.
- Set the height of the ticknessing table. (see «Height adjus-
ment of the ticknessing table»).
- Place the surface already planed onto the thicknessing
table (D). Support the board well in order to avoid an
indentation.
- Push the board in so far until it is grabbed by the infeed
rollers (Z).
- Let the board pass without pushing.
- Repeat the procedure until a smooth, well planed surface
is obtained.
- Support the board at the end of the passage, so that the
tool cannot create an indentation mark (41)
Important : An indentation mark of 1/10 of mm is acceptable.
(see detail) (41)
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach KITY 439 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KITY 439 in the language / languages: English, German, French as an attachment in your email.

The manual is 1.83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info