782080

Scheppach KITY 439 Manual

35
Zoom out
Zoom in
Previous page
1/80
Next page
DGB
34
6. INBETRIEBNAHME DER MASCHINE
h. Stromanschluss
i. Staubabsaugung
Anschlussdurchmesser an der
Maschine
Optimale Luftgeschwindigkeit in den
Schläuchen
Luftleistung 565 m3/h
20 m/s
100 mm
6. PUTTING THE MACHINE INTO OPERATION
h. Electric connection
i. Elimination of sawdust
Connection dia. on machine
Optimum flow rate in the hoses
Air capacity 565 m3/h
20 m/s
100 mm
Nach Anschluss der Drehstrommaschine überprüfen Sie die
Drehrichtung des Werkzeugs. Bei Bedarf tauschen Sie 2 der
3 Phasenadern aus (Umkehrung der 2 Phasen im Stecker
mithilfe eines Schraubendrehers), um die richtige Drehrichtung
zu erhalten.
Bei einem Wechsel des Anschlusses an das Drehstromnetz
(mehrere eingebaute Steckdosen) muss die Drehrichtung
jedes Mal neu überprüft werden.
Wenn die Länge des Anschlusskabels 10 m übersteigt, muss
der Minimumquerschnitt 2,5 mm² betragen.
Schließen Sie das Kabel an das Schaltergehäuse (20) der
Maschine an und verbinden Sie es mit einer gut zugänglichen
und vorschriftsmäßig geerdeten EEC-Steckdose.
Die elektrischen Anschlüsse innerhalb der Maschine wurden
im Werk betriebsfertig hergestellt.
Anschlüsse und Reparaturen an der elektrischen Installation
dürfen nur von einem Elektrofachmann ausgeführt werden.
- Der Anschluss an eine Späne- und Staubabsaugung
ist zwingend vorgeschrieben, um die Hygiene- und
Sicherheitsvorschriften zu erfüllen, und um das gute
Funktionieren der Maschine zu gewährleisten (19). (Siehe
die im Katalog als Sonderzubehör angebotene Kity-
Absauganlage.)
- die flexiblen Schläuche müssen entflammbar sein.
- Maschine und Absauganlage müssen gleichzeitig anlaufen.
(Siehe Katalogzubehör Kity-Einschaltautomatik.)
- Die an die Maschine angeschlossene Absauganlage muss
folgende Minimumeigenschaften haben :
Once the three-phase machine has been connected to
the power supply, check the direction of rotation of the tool.
If needed, interchange the 2 phase leads (reversal of the 2
phases in the plug using a screw driver), in order to get the
proper direction of revolution.
Every time the connection to a three-phase mains supply is
changed (several built-in sockets), the direction of rotation
must be checked anew.
If the length of the connecting cable exceeds 10 m, the
minimum cross-section must be 2.5 mm².
Connect the cable to the switch casing (20) of the machine
and a well accessible and properly earthed EEC socket.
The electrical connections within the machine have been
prepared, ready for use, in the works.
Connections and repairs of the electric installation may only be
executed by a qualified electrician.
- The connection of a chip and dust extractor unit is
imperative, in order to meet the hygienic and safety
regulations and to ensure the good functioning of the
machine (19). (See Kity dust extractor unit offered in the
catalogue as special equipment.)
- Flexible ducts have to be not easily ignitable.
- Machine and suction unit must start simultaneously. (See
Kity catalogue for optional «automatic switch-on system».)
- The suction unit connected to the machine must have the
following minimum characteristics :
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach KITY 439 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KITY 439 in the language / languages: English, German, French as an attachment in your email.

The manual is 1.83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info