782035

Scheppach HTH250 Manual

25
Zoom out
Zoom in
Previous page
1/104
Next page
25GB
Pay attention to breeding birds in the hedge. If so, put
off hedge trimming or leave this area out.
At any case pay attention to all safety instructions.
10. Maintenance
Before each maintenance and cleaning work
- Stop the engine.
- Wait until the cutting device does not longer move.
- Stop the engine and pull off the spark plug connector
(with the exception of idle speed adjustment).
Do not carry out maintenance work close to open
ames. Risk of re.
Maintenance and repair work other than those de-
scribed in this chapter is only allowed to be carried out
by service staff.
For maintaining and cleaning, removed security
devices must unconditionally be mounted properly
and proved again.
Use only original parts. Other parts can result in unex-
pected damages and injuries.
In order to aviod possible injuries wear gloves.
To guarantee a long and reliable usage of the hedge
trimmer carry out the following maintainance works
regularly.
Check the hedge trimmer for obvious defects such
as
- loose fastening elements
- worn or damaged components
- deformed, broken or damaged cutting device
- leaks from the fuel tank cap or fuel lines
Check the hedge trimmer after each application for
- wear and tear, in particular sliding play of the cutting
device
- correct assembly and faultless covers and protective
devices.
Necessary repair or maintainance operations have to
be carried out before the usage of the hedge trimmer.
Adjusting the cutting device
Readjust the sliding play if cut material is clamped be-
tween the blades or the play has increased due to nor-
mal wearing of the cutting device after a longer period
of use.
To obtain good cutting results the free motion between
the blades and the sword must be correctly adjusted.
For this proceed as follows:
1. Loosen the nuts (A) on the top surface of the cut-
ting device.
2. Slightly tighten the screws (B) on the underside (if
required loosen them previously).
3. Turn the screw back anticlockwisely by a quarter
up to a half turn.
4. Use a screwdriver to hold the screw and rmly
tighten the nuts.
The sliding play is correctly adjusted if the washer under
the screw head can just be freely moved back and forth
by hand.
• If you release the throttle trigger the cutting device
will afterrun for a short time (free wheeling effect).
• Start trimming with the cutting device moving.
• Never touch the cutting device with your hands during
operation.
• Never work
- with stretched arms
- on hardly accessible places
- too far bent forward
• Never work with the hedge trimmer above shoulder
height.
• Never get in contact with the running cutting device
with metallic fences or the ground.
• Stop the engine and pull the spark plug connector:
- when you notice changes in the device’s behaviour,
- to remove jammed material,
- to check the cutting device after it had contact with
stones, nails or other hard objects,
- to eliminate faults,
- for work breaks,
- before leaving the hedge trimmer.
• Do not place a hot hedge trimmer in dry grass or onto
inammable objects.
• Before starting your work make sure that:
- no other persons or animals stay within the working
area,
- you can always step back without any barriers,
- your standing area is free from foreign objects,
brushwood and branches,
- you have always a secure standing position.
If persons who have blood circulation problems are too
often exposed to vibrations damages to the nervous
system or to blood vessels may occur.
You can reduce vibrations
- by thick and warm working gloves,
- shorter working time (have longer breaks).
See a doctor if your ngers swell, you don’t feel well or
your ngers become numb.
Working with the hedge trimmer
Hold the hedge trimmer with both hands on a safe
distance from the body.
• The maximal diameter to cut depends on the wood’s
type, age, moisture and hardness.
• Therefore cut very thick branches using branch shears
to your desired length before trimming the hedge.
• Due to its double sided knives the hedge trimmer can
be guided forward and backward or by oscillating
movements from one to another side.
• At rst cut the sides of the hedge and then the upper
edge.
• Cut the hedge from the bottom up.
• Cut the hedge in trapezium shape.
• Stretch a guide over the complete length of the hedge
when you want to shorten the upper edge of the
hedge evenly.
• Trim in several passes if you have to cut down a large
portion of the hedge.
Best time for hedge trimming:
• Leaved hedge: June and October
• Conifer hedge: April and August
• Quickly growing hedge: from May and then every 6
weeks
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HTH250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HTH250 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 4.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info