782092

Scheppach HT1050 Manual

21
Zoom out
Zoom in
Previous page
1/108
Next page
21
Putting into operation
Attention! Device must be unplugged from mains
during any retooling or assembly work
Dust extraction Fig. 6,7
When used in enclosed rooms, the machine must be
connected to a dust extractor unit.
Connecting the dust extractor for surface planing:
• Set the thicknessing table to the lowest position and
push the suction connector into the machine until both
switching pins (I) can slide into the mortises (H) (Fig.
6).
• Finally, fasten the exhaust hood on the jointing
table with a threaded pin Fig. 7.
Connecting the dust extractor for thicknessing (Fig.
8.0, 8.1, 8.2)
• Loosen the clamping lever (D, Fig.4) and push back
the stop rail (C) up to the stop bolt (E)
• Adjust the stop at an inclination of 45°
• Push the knife cover back
• Lift the arm (G) of the planer shaft guard so that the
slotted holes (H) are exposed
• Push the exhaust nozzles (4) under the arm (G)
till both switching plungers (I) are balanced to the
slotted holes (H). (Fig.8.1)
• Insert the switching plungers (1) into the slotted
holes
• Fasten the exhaust hood (4) on the jointing table
with the knurled screw (K) (Fig.8.2)
• Push the knife cover over the exhaust nozzles
Mise en service
Attention ! Avant tout travaux de rééquipement et de
montage, débrancher la che d’alimentation
Aspiration de poussière Fig. 6,7
Si la machine est utilisée dans des locaux fermés, elle
doit être reliée à un dispositif d’aspiration.
Raccord de l’aspiration pour le dégauchissage:
• Mettre la table à la position la plus basse et pousser
la buse d’aspiration dans la machine jusqu’au point où
les deux boulons commutateurs (I) se laissent pousser
dans les trous oblongs (H) (Fig. 6).
• Enn, xez la hotte aspirante avec un boulon leté sur
la table de dégau Fig. 7.
Raccord de l’aspiration pour le rabotage (Fig. 8.0,
8.1, 8.2)
• Desserrez le levier de serrage (D, Fig.4) et pous-
sez la barre de butée (C) jusqu’à la vis de butée
(E).
• Réglez la butée à un angle de 45°.
• Faites glisser le protège-lame.
• Soulevez le bras (G) de la protection de l’arbre de
dégau, de sorte que le trou oblong (H) soit exposé.
• Faites glisser le manchon d’aspiration (4) sous le
bras (G) jusqu’à ce que le poussoir de commande
(I) et le trou oblong (H) soient alignés (H) (Fig. 8.1).
• Poussez le poussoir de commande (l) dans le trou
oblong.
• À l’aide de la vis moletée (K), xez la hotte aspi-
rante (4) sur la table de dégau (Fig.8.2).
• Faites glisser le protège-lame sur le manchon
d’aspiration.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HT1050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HT1050 in the language / languages: English, German, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info