782092

Scheppach HT1050 Manual

19
Zoom out
Zoom in
Previous page
1/108
Next page
19
Transport
For transport, the machine may only be lifted on the
base. Never lift it on the guards, the setting handles or
the planer/thicknesser table.
Before transporting, pull the power supply plug.
During transport, the cutter block guard must be set in
the lowest position.
Unpacking the machine
Check the contents of any possible transport damage.
In case of a damage, inform immediately the forward-
ing agent. Check the contents for completeness. Inform
immediately the dealer in case of any missing parts.
The complete machine is shipped in one single carton
box. Any additional parts that have to be attached to
the machine, must be identied before starting the as-
sembly.
Fig. 2
1 Planing and thicknessing machine
2 Ripping fence
3 Handle
4 Suction connector
Assembly
Assembling trimming endstop unit Fig. 3
Attention! Device must be unplugged from mains during
any retooling or assembly work
Install the jointing bracket (A) with 2 inner hexagon bolts
(B) M5x20mm to the side wall of the jointing table.
Justifying the trimming endstop Fig. 4
Postion the endstop at a 90 ° angle, and clamp it in place
with the toggle screw (H). Now place the cross-slotted
screw (F) against the endstop and secure it with the
nut. Then position the endstop at 45° and clamp it in
place with the clamping screw (H). Next, place the allen
screw (G) against the endstop and secure it with the nut.
Now check both brackets with a sample and re-justify
the scale if required.
Adjusting the stop rail Fig.4
The stop rail (C) in the area of the stop bolt (E) can be
displaced by loosening the clamping lever (D).
Planer shaft guard Fig. 5
The clamping handle (J) serves the purpose of lifting
and xing the planer shaft guard (K)
Transport
Pour transporter, n’attacher le dispositif de relevage
qu’au bâti, jamais aux dispositifs protecteurs, aux poi-
gnées de réglage ou à la table de dégauchissage.
Pour le transport, débrancher la prise d’alimenta-
tion.
Lors du transport, le protecteur de l’arbre de rabotage
doit se trouver dans la position la plus basse.
Déballage de la machine
Vérier dès la livraison, qu’aucune pièce n’ait été dé-
tériorée pendant le transport. En cas de réclamation,
informer aussitôt le livreur. Vérier que la livraison soit
bien complète. En cas de réclamation, informer aussitôt
le vendeur.
La machine est expédiée dans un seul carton. Des
accessoires supplémentaires doivent être localisés et
identiés avant le début du montage.
Fig. 2
1. Raboteuse-dégauchisseuse
2. Butée de rabotage
3. Poignée
4. Manchon de prise d’air
Montage
Montage butée de dressage Fig. 3
Attention ! Avant tout travaux de rééquipement et de
montage, débrancher la che d’alimentation
Installez le support de dégau (A) avec 2 vis à tête
hexagonale (B) M5 x 20 mm à la paroi latérale de la
table de dégau.
Alignement de la butée de dressage Fig. 4
Régler la butée à un angle de 90 ° et la serrer avec la
vis à clé (H). Régler la vis à fente (F) jusqu’à la butée et
la bloquer avec l’écrou. Puis régler la butée sur 45° et
bloquer avec la vis à clé (H). Ensuite régler la vis Allen
(G) jusqu’à la butée et bloquer avec l’écrou.
Vérier les angles à l’aide d’un échantillon et régler de
nouveau l’échelle (I) si cela est nécessaire.
Réglage de la barre de butée Fig. 4
En desserrant le levier de serrage (D), la barre de butée
(C) peut être réglée dans les vis de butée (E).
Protection de l'arbre de dégau Fig. 5
La poignée de blocage (J) sert à verrouiller la protection
de l'arbre de dégau (K).
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HT1050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HT1050 in the language / languages: English, German, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info