782563
43
Zoom out
Zoom in
Previous page
1/72
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 43
2. Turn the hexagon screw (1a) counterclockwise with
the ring spanner 10/13 mm (26) to undo the hexa-
gon screw (1a).
3. Hold the saw blade (1) carefully with one hand
4. Remove the hexagon screw (1a) and outer saw
blade ange (1b) from the drive shaft.
5. Now remove the saw blade (1) from the drive shaft
and carefully draw it up and out of the saw table (5).
15.4.4 Fitting the saw blade (g. 38 + 39)
1. Clean the external and internal saw blade ange
(1c/1b) carefully, before tting a new saw blade (1).
2. Place a new saw blade (1) on the drive shaft. Ob-
serve the rotational direction: The cutting angle
of the teeth must point in the running direction
(forwards). The running direction is usually also
marked on the saw blade.
3. Fit the outer saw blade ange (1b) back on the
drive shaft. Ensure the correct alignment of the
outer saw blade ange (1b).
4. Screw the hexagon screw (1a) tight onto the drive
shaft with the hand.
5. Carefully turn the saw blade (1) in the running
direction: It must be precisely centred and must
not “wobble”. Check that the saw blade (1) and
outer saw blade ange (1b) are seated correctly.
Align the parts once more, if the saw blade is not
precisely centred.
m WARNING
Warning against unexpected hazards and dam-
ages to the product
- Check the setting of the saw blade after every
saw blade replacement.
6. Hold the outer saw blade ange (1d) in position
with the open-ended spanner 10/21 mm (27).
7. Turn the hexagon screw (1a) tight in a clockwise
direction with the open-ended spanner 10/13 mm
(26).
8. Mount the table inlay (4) and the saw blade guard
(2) (see 9.3.3 and 9.4.1).
9. Check the correct setting of the riving knife (see
9.3.2).
15.5 Service information
With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Wearing parts*:Carbon brushes, table inlay, push
stick, saw blade
* May not be included in the scope of delivery!
16. Storage
m WARNING
Danger of injury due to unexpected start-up of the
machine
- Remove the mains plug from the socket.
Check the nuts, pins and screws for rm seating.
Check the covers and protective equipment for
damage and correct seating.
Check the electrical connections. Repairs to the
electrical connections may only be carried out by a
specialist workshop.
15.2 Oiling the product
1. Oil the rotating parts once monthly to extend the
life of the tool.
2. Do not oil the motor.
15.3 Servicing carbon brushes
ATTENTION
Product damage
- The carbon brushes must only be replaced by
an electrician.
If excessive sparks are generated, have an electri-
cian check the carbon brushes.
15.4 Replacing the saw blade
m WARNING
Danger of injury! Improper handling of the circular ta-
ble saw may result in serious injury.
m WARNING
Danger of injury due to unexpected start-up of the
machine
- Remove the mains plug from the socket.
m WARNING
Danger of injury for ngers and hands due to sharp
edges
- Wear protective gloves.
15.4.1 Removing the saw blade guard (g. 19)
1. Turn the saw blade (1) to the maximum position
out of the saw table (5) by turning the crank wheel
(16) clockwise until it reaches the stop.
2. Loosen the xing screw (2a).
3. Carefully slide the saw blade guard (2) over the
riving knife (3).
15.4.2 Removing the table inlay (g. 16)
1. Loosen the xing screw (4a).
2. Remove the table inlay (4).
3. Check the table inlay (4) for damage. Replace the
table inlay if it is damaged or no longer connects
ush with the saw table.
15.4.3 Removing the saw blade guard (g. 38 + 39)
PREREQUISITE: The saw blade (1) has been set to
the maximum cutting depth (see 11.2).
1. Place the ring spanner 10/21 mm (27) on the outer
saw blade ange (1b) and secure the drive shaft
in this way.
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HS116 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS116 in the language / languages: English, German, French as an attachment in your email.

The manual is 6.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info