Manual Scheppach HS116 (page 40 of 72) (English, German, French)

782563

Zoom out

Zoom in

1/72

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

40 | GB

11.7 Using the sliding carrier plate (g. 31)

1. To use the sliding carrier plate (21), pull down the

wing nut (21a) and turn it 90°.

2. Release the wing nut (21a) again so that it engag-

es again.

3. The sliding carrier plate (21) is unlocked and you can

freely move it forwards and backwards.

4. To lock the sliding carrier plate (21), bring it back to

its starting position.

5. Pull the wing nut (21a) down and turn it 90° again.

6. Release it so that it engages again.

7. The sliding carrier plate (21) is locked.

12. Sawing

m WARNING

Danger of injury due to incorrect mounting

- Check that the product is properly assembled.

- Check the saw blade for mobility and the moving

parts for ease of movement.

ATTENTION

Wait after the saw has been switched on, until the

saw blade (1) has reached full speed, before starting

the cutting process.

12.1 Working instructions

m WARNING

Danger of injury!

Improper handling may result in serious injury.

- Observe and follow the safety and working in-

structions.

• When making longitudinal cuts, do not stand in front

of the circular table saw, but position yourself at an

angle to the cut.

• Always use the parallel stop for angled cuts.

• Use a push stick or wooden push block in order to

guide the workpiece past the saw blade. Replace a

damaged or worn push stick.

• Secure larger workpieces against tipping after the

cutting process. To do so, use for example a reel-

o󰀨 stand.

• After the circular table saw has been switched on,

wait until the saw blade has reached full speed, be-

fore starting the cutting process.

• Only operate the table saw with an extraction system.

• After every new setting, we recommend performing

a test cut, in order to check the dimensional settings.

• Check and clean the extraction channels at regular

intervals.

12.2 Performing longitudinal cuts (g. 32)

With a longitudinal cut, you cut a workpiece in its lon-

gitudinal direction. Hold the edge of the workpiece

against the parallel stop (8), whilst the at side lies on

the saw table (5).

1. Adjust the parallel stop (8) according to the work-

piece height and the desired width (see 11.4).

2. Set the saw blade (1) to the maximum cutting

depth. (see 11.2)

3. Position the parallel stop (8) such that the stop rail

(8a) makes contact with the saw blade (1).

4. If the stop rail (8a) is not in line with the saw blade

(1), loosen the hexagon screws (8c) in the parallel

stop (8) with a hexagon spanner and align the stop

rail (8a) parallel to the saw blade (1).

5. Tighten the hexagon screws (8c) again.

6. Again, position the parallel stop (8) away from the

saw blade (1).

11.5 Using the transverse stop (Fig. 23)

Do not push the stop rail (19b) too far towards the saw

blade (1). The distance between the stop rail (19b)

and the saw blade (1) needs to be approx. 2 cm.

11.5.1 Setting the transverse stop (g. 23)

1. Secure the stop rail (19b) on the transverse stop

(19) by tightening the knurled nuts (19d).

2. Slide the transverse stop (19) into one of the two

guide grooves of the saw table (5).

3. Loosen the clamping handle (19c) and turn the trans-

verse stop (19) until the desired angle has been set.

4. Tighten the clamping handle (19c) again.

5. To secure the transverse stop (19) on the slid-

ing carrier plate (21), tighten the wing nut for the

transverse stop (19f).

11.5.2 Using the screw clamp on the transverse

stop (g. 23)

1. Fit the screw clamp (19a) on the transverse stop

(19).

2. Secure the screw clamp (19a) on the required

height by tightening the wing nut for the screw

clamp (19e).

11.6 Table width extensions

11.6.1 Pulling out the left table width extension

(g. 29)

1. To pull out the left table width extension (20), loos-

en the two wing nuts (20a) on the front and rear of

the machine.

2. Pull out the left table width extension (20) to the

desired length.

3. Secure this position by tightening the two wing

nuts (20a) again.

11.6.2 Pulling out the right table width extension

(g. 1 + 30)

1. To pull out the right table width extension (20),

loosen the locking lever for the right table width

extension (11). (g. 1)

2. Pull out the right table width extension (9) to the

desired length. (g. 30)

3. Secure this position by tightening the locking lever

for the right table width extension (11) again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS116 in the language / languages: English, German, French as an attachment in your email.

The manual is 6.03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HS116 Manual

Product: