Manual Scheppach HS100S (page 13 of 86) (English, German, Polish)

781486

Zoom out

Zoom in

1/86

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

13 І 86

4. Loosen the mounting bolt (24) in order to pull out

the splitting wedge (6) until the right distance is

adjusted (g. 10).

5. Tighten the mounting screw (24) again and mount

the bench insert (2).

8.4 Mounting / dismounting the saw blade guard

(gs. 11-12)

1. Mount the saw blade guard (6) together with the bolt

(25) on top of the riving knife (6), so that the bolt is

rmly seated in the slot of the riving knife (6).

2. Do not screw in the bolt (25) too tightly; the saw

blade guard (6) must move freely.

3. Plug the suction hose (5) onto the suction adapter

(26) and the connecting piece of the saw blade

guard (4). Connect a suitable splint collector onto

the suction adapter (26).

4. Disassembly is performed in reverse order.

Caution!

The saw blade guard (4) must be lowered onto

the workpiece before starting the sawing opera-

tion.

8.5 Replacing the bench insert (g. 8)

1. In case of wear or damage, the bench insert (2)

must be replaced; otherwise, there is an increased

risk of injury.

2. Unfasten the bolt (23) using a Phillips screwdriver.

3. Take out the worn bench insert (2).

4. The installation of the new bench insert is done in

reverse order.

8.6 Installing / replacing the saw blade (g. 13)

1. Caution! Pull out the main plug and wear safety

gloves.

2. Dismount the saw blade guard (4) (see 8.4)

3. Remove the bench insert (2) (see 8.5)

4. Loosen the nut by placing a saw blade spanner

(21a) on the nut while holding up another saw blade

spanner (21b) on the motor shaft (see g. 22).

5. Caution! Turn the nut in the direction of rotation of

the saw blade.

6. Remove the outer ange and remove the old blade

inner ange.

7. Clean the saw blade ange thoroughly with a wire

brush before mounting the new saw blade.

8. Insert the new saw blade in reverse order and

tighten.

Caution! Note the direction of run, the cutting

slope of the teeth must be in the direction of run,

i.e. facing forward.

9. Remount and adjust the bench insert (2) and saw

blade guard (4) (see 8.4 and 8.5)

10. Before you start working again with the saw, check

proper functioning of the safety equipment.

9. Using the saw

9.1 On/Off switch (Fig. 14)

- The saw can be switched on by pressing the green

pushbutton „I“. (11)

- The red pushbutton „0“ (11) has to be pressed to

switch off the saw.

9.2 Cutting depth (Fig. 14)

Turn the round handle (12) to set the blade (3) to the

required cutting depth.

- Anticlockwise: smaller cutting depth

- Clockwise: larger cutting depth

After each new adjustment it is advisable to carry out a

trial cut in order to check the set dimensions.

8. Attachment

Important. Pull out the power plug before carrying

out any maintenance, resetting or assembly work on

the circular saw!

Place all parts supplied on a at surface. Grouping

equal parts.

Note: If compounds with a bolt (round head / or hexa-

gon), hex nuts and washers are backed up, the washer

must be tted under the nut.

Insert screws each from outside to inside. Secure con-

nections with nuts on the inside.

Note: Tighten the nuts and bolts during assembly only

to the extent that they can not fall down.

If you tighten the nuts and bolts prior to nal assembly,

nal assembly can not be performed.

8.1 Mounting the bench extension (g. 5)

1. Turn the saw and place it on the oor with the

bench facing down.

2. Align the bench extension (8) ush with the saw

bench (1).

3. Push table extension (8) onto the sawing table

(1) using the hex bolts (19) and loosely fasten the

spring washers (20a), washers (20b) and hex nuts

(20). Repeat for the opposite side.

4. Screw the support struts (22) to the table extensi-

ons (8) with the hex bolts (19), spring washer (20a),

and washers (20b).

5. Subsequently, tighten all screws.

8.2 Mounting rack (gs. 6-7)

1. Screw the four support legs (18) together with the

support struts (22) onto the saw with the hex bolts

(19), the spring rings (20a) and the washers (20b)

(g. 6). For this use the saw blade key (21a), part of

the delivery contents (g. 6).

2. Now place the rubber feet (16a) onto the support

legs (16) (g. 6.1).

3. Now, screw the long centre brace (18) and the short

centre brace (17) onto the legs (16) using the hexa-

gon head bolts (19) and the hexagon head nuts (20).

Make sure that the same braces face each other.

The long centre braces (18 - marked „B“) must

be mounted parallel to the operator‘s side of the

saw. (Fig. 7).

4. Using two hex bolts (19) on each, loosely secure the

spring washers (20a), washers (20b) and hex nuts

(20) at the drill holes of the rear support legs of the

support frame (16b) (g. 7.1).

Attention!

Both support frames must be fastened to the

back of the machine!

5. Then, tighten all the nuts and bolts of the under-

frame.

8.3 Setting / mounting the riving knife (gs. 8-10)

m The setting Caution! Pull out the main plug!

The setting of the riving knife (6) must be checked

prior to commissioning. of the riving knife (6) must

be checked prior to commissioning.

1. Set the saw blade (3) to the max. cutting depth,

bring it to the 0° position and lock it.

2. Unfasten the bolt (23) from the bench insert (2)

using a Phillips screwdriver, and remove bench

insert (22) (g.8).

3. The distance between the saw blade (3) and the

riving knife (6) must be max. 5 mm. (Fig. 9)

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS100S in the language / languages: English, German, Polish as an attachment in your email.

The manual is 5.78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HS100S Manual

Product: