644509

Scheppach hmc 3200 ci Manual

24
Zoom out
Zoom in
Previous page
1/157
Next page
Documentation
9322 0311
Page:24
GENERAL NOTES
After unpacking, check all components for possible damage occurring during transportation. Delivery personnel must
be informed immediately of any claims.
Claims made at a later date will not be recognised.
Check that the delivery is complete.
Before using, familiarise yourself with the machine with the help of the operating instructions.
For accessories, replacement and spare parts, use only original scheppach components.
Spare parts can be obtained from your scheppach dealer.
When ordering, state our item numbers as well as the model and year of the device.
In these operating instructions, we have highlighted notes relating to your safety with the following sign.
Pass on these safety notes to everyone who works at the machine.
Observe all safety and hazard notices on the machine.
Maintain all safety and hazard notices on the machine in a legible condition.
Caution when operating: Danger of injury to fingers and hands by the rotating cutting tool.
Maximum planing block rotational speed 6500 1/min.
The planing block was manufactured in accordance with the DIN EN 847-1.
Make sure that the machine is standing stable on firm ground.
Only begin the working cycle when the full rotational speed has been reached.
Check the lines to the power connection. Do not use faulty lines. See Electrical connection.
Make sure that the planing machine is standing stable on firm ground when mounting.
Keep children away from the machine when it is connected to the electricity supply.
The operator must be at least 18 years old. Trainees must be at least 16 years old, but may only work at the machine
under supervision.
Persons working at the machine must not be distracted.
The operating station of the machine must be kept free of shavings and waste wood.
Wear tight-fitting clothes. Remove jewelry, rings and wrist-watches.
Pay attention to the rotational direction of the motor and tool, see “Electrical connection planing machine”.
The safety devices on the machine may not be removed or rendered unusable.
When working at the machine, all protective devices and covers must be installed.
Equipping, adjusting, measuring and cleaning work may only be carried out with the motor is switched off. Pull out the
plug and wait for the rotating tool to come to a standstill.
The complete protective and safety devices must be remounted following repair and maintenance work.
Installation, repairs and maintenance on the electric installation may only be carried out by qualified professionals.
When correcting faults, switch the machine off. Pull out the plug.
The grippers have to be smooth-running and free of particles.
An exhaust system should be used to remove wood shavings and sawdust. The flow rate at the suction nozzle must be at
least 20 m/s.
Only work with sharpened planing knives. Blunt planing knives increase the danger of kickback.
Defective planing knives (splits or similar) are to be replaced immediately. See Knife replacement.
The planing block guard should always be adjusted to the width of the workpiece. The part of the knife block not in use
must be covered.
When planing short workpieces, a feed loader must be used.
With inset work, always use the settings that prevent the tool backfiring.
Check the effectiveness of the kickback prevention device before every shift. The claw points must be square-edged.
When leaving the workplace, switch off the motor. Pull out the plug.
The complete protective and safety devices must be remounted following repair and maintenance work.
Even when only moving the machine a short distance, disengage it from every external energy supply! Before bringing the
machine into service again, reconnect it to the mains carefully
The workpiece has to be checked for possible defects, as foreign bodies, knots, depressions, chatter marks, torsions,
before start of work.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach hmc 3200 ci at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach hmc 3200 ci in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 11.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach hmc 3200 ci

Scheppach hmc 3200 ci Additional guide - All languages - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info