Manual Scheppach HM90MP (page 29 of 168) (English, German, French, Italian, Polish, All languages)

781435

Zoom out

Zoom in

1/168

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 29

• Workpiece supports (8) must always be secured

and used during work. Set the desired table size

by loosening the set screw (9). Then tighten the set

screw (9) again.

8.2 Precision adjustment of the stop for crosscut

90° (g. 1, 2, 5, 6)

No stop angle included.

• Lower the machine head (4) and secure it using the

locking bolt (23).

• Loosen the set screw (22).

• Position the angle stop (A) between the saw blade

(6) and the rotary table (14).

• Loosen the lock nut (26a).

• Adjust the adjusting screw (26) until the angle be-

tween the saw blade (6) and rotary table (14) is 90°.

• Re-tighten the lock nut (26a).

• Subsequently check the position of the angle indi-

cator. If necessary loosen the pointer (19) using a

Philips screwdriver, set to position 0° on the angle

scale (18) and re-tighten the retaining screw.

8.3 Crosscut 90° and turntable 0° (g. 1, 2, 7)

In the case of cutting widths up to approx. 100 mm it

is possible to x the traction function of the saw with

the set screw (20) in the rear position. In this position

the machine can be operated in cross cutting mode. If

the cutting width is over 100 mm then it is necessary

to ensure that the set screw (20) is loose and the ma-

chine head (4) can move.

Attention!

For 90° crosscuts, the moveable stop rail (16a) must

be xed in the inner position.

• Open the set screw (16b) for the moveable stop rail

(16a) and push the moveable stop rail (16a) inwards.

• The moveable stop rail (16a) must be locked in a

position far enough from the inner position that the

distance between the stop rail (16a) and the saw

blade (6) is no more than 8 mm.

• Before making the cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Re-tighten the set screw (16b).

• Move the machine head (4) to its upper position.

• Use the handle (1) to push back the machine head

(4) and x it in this position if required (dependent on

the cutting width).

• Place the piece of wood to be cut at the stop rail (16)

and on the turntable (14).

• Lock the material with the clamping devices (7) on

the xed saw table (15) to prevent the material from

moving during the cutting operation.

• Release the lock switch (3) and press the ON/OFF

switch to start the motor.

• With the drag guide (21) xed in place:

use the handle (1) to move the machine head (4)

steadily and with light pressure downwards until the

saw blade (6) has completely cut through the work

piece

• Pull out the pre-installed tilt protection (35) com-

pletely and secure it with an Allen key.

• Adjust the adjusting screw (36) to the level of the

tabletop to avoid wobbling of the machine.

• All covers and safety devices have to be properly

tted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws, etc.

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power

supply make sure the data on the rating plate are

dentical to the mains data.

7.1 Checking the moving saw blade guard safe-

ty device (5)

The saw blade guard protects against accidental con-

tact with the saw blade and from chips ying around.

Check function

To do so, fold the saw downwards:

• The saw blade guard must provide free access to

the saw blade without touching other parts.

• When folding the saw upwards into the starting

position, the saw blade guard must cover the saw

blade automatically.

8. Attachment and operation

8.1 Assembling the trim, chop and mitre saw

(g. 1, 2, 4, 5, 21)

• In order to adjust the rotary table (14), fold the lock-

ing handle (11) upwards and pull up the latched po-

sition lever (34) with your index nger.

• Turn the rotary table (14) and pointer (12) to the de-

sired angle measurement of the scale (13). To x

the setting, fold the locking handle (11) downwards.

• Pressing the machine head (4) lightly downwards

and removing the locking bolt (23) from the motor

bracket at the same time disengages the saw from

the lowest position.

• Swing the machine head (4) up.

• It is possible to secure the clamping devices (7) to

the left or right on the xed saw table (15). Insert

the clamping devices (7) in the holes on the rear

side of the stop rail (16) and secure it with the star

grip screws (7a).

• You can press the quick locking button (7b) to ad-

just the clamping device’s pressure plate (7) easily

to the workpiece height.

• For 0°- 45° mitre cuts, the clamping device (7) must

only be mounted on the right side (see g. 11-12).

• It is possible to tilt the machine head (4) a max. 45°

to the left by loosening the set screw (22).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HM90MP in the language / languages: English, German, French, Italian, Polish, All languages as an attachment in your email.

The manual is 7.28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HM90MP Manual

Product: